Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2020.11
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0417591 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


B150964N37
3.354,0.083 3.76,0.323 0.406,0.24 3.448,0.115 3.74,0.313 0.292,0.198 10 false J18

a.

Disconnect the J18 multiplex network master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
J18-11 (B) - J18-12 (GND) Power supply Always*1 11 to 14 V
Ignition switch off*2
J18-12 (GND) - Body ground Ground Always Below 1 Ω

·

*1: for Gasoline Model

·

*2: for HV Model



c.

Reconnect the J18 multiplex network master switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
J18-15 (DOWN) - J18-12 (GND) Power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or not pulled 11 to 14 V
J18-15 (DOWN) - J18-12 (GND) Power window motor DOWN output Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
J18-20 (UP) - J18-12 (GND) Power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or not pulled 11 to 14 V
J18-20 (UP) - J18-12 (GND) Power window motor UP output Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


B351350C03
3.75,0.188 4.167,0.458 0.417,0.271 2.896,0.188 3.313,0.458 0.417,0.271 3.885,0.25 4.198,0.448 0.313,0.198 10 false J33 3.063,0.25 3.375,0.448 0.313,0.198 10 false J3 3.354,0.26 3.698,0.531 0.344,0.271 10 false *A 4.219,0.26 4.563,0.531 0.344,0.271 10 false *B
*A for LHD *B for RHD


a.

Disconnect the J3*1 or J33*2 power window regulator switch assembly connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J3-7 (GND) - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J33-7 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the J3*1 or J33*2 power window regulator switch assembly connector.

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J3-5 (UP) - J3-7 (GND) Power window motor UP output Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
J3-5 (UP) - J3-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
J3-5 (UP) - J3-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window fully open 11 to 14 V
J3-5 (UP) - J3-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J3-5 (UP) - J3-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J3-4 (DOWN) - J3-7 (GND) Power window motor DOWN output Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
J3-4 (DOWN) - J3-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
J3-4 (DOWN) - J3-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J3-4 (DOWN) - J3-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J3-4 (DOWN) - J3-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window fully open 11 to 14 V
J3-8 (AUTO) - J3-7 (GND) Power window motor AUTO UP output Ignition switch ON, front passenger door power window fully open 11 to 14 V
J3-8 (AUTO) - J3-7 (GND) Power window motor AUTO UP output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J3-8 (AUTO) - J3-7 (GND) Power window motor AUTO UP output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J3-8 (AUTO) - J3-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J3-8 (AUTO) - J3-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J3-8 (AUTO) - J3-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, front passenger door power window fully open 11 to 14 V

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J33-5 (UP) - J33-7 (GND) Power window motor UP output Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
J33-5 (UP) - J33-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
J33-5 (UP) - J33-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window fully open 11 to 14 V
J33-5 (UP) - J33-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J33-5 (UP) - J33-7 (GND) Power window motor UP output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J33-4 (DOWN) - J33-7 (GND) Power window motor DOWN output Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
J33-4 (DOWN) - J33-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
J33-4 (DOWN) - J33-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J33-4 (DOWN) - J33-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J33-4 (DOWN) - J33-7 (GND) Power window motor DOWN output Ignition switch ON, front passenger door power window fully open 11 to 14 V
J33-8 (AUTO) - J33-7 (GND) Power window motor AUTO UP output Ignition switch ON, front passenger door power window fully open 11 to 14 V
J33-8 (AUTO) - J33-7 (GND) Power window motor AUTO UP output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J33-8 (AUTO) - J33-7 (GND) Power window motor AUTO UP output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J33-8 (AUTO) - J33-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J33-8 (AUTO) - J33-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J33-8 (AUTO) - J33-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, front passenger door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR)


B351350N13
3.375,0.208 3.792,0.479 0.417,0.271 3.531,0.26 3.844,0.458 0.313,0.198 10 false K7

a.

Disconnect the K7 rear power window regulator switch assembly (for LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
K7-7 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the K7 rear power window regulator switch assembly (for LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
K7-5 (UP) - K7-7 (GND) Power window motor UP output Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
K7-5 (UP) - K7-7 (GND) Power window motor UP output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
K7-5 (UP) - K7-7 (GND) Power window motor UP output Ignition switch ON, rear LH door power window fully open 11 to 14 V
K7-5 (UP) - K7-7 (GND) Power window motor UP output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
K7-5 (UP) - K7-7 (GND) Power window motor UP output Ignition switch ON, rear LH door power window fully closed 11 to 14 V
K7-4 (DOWN) - K7-7 (GND) Power window motor DOWN output Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
K7-4 (DOWN) - K7-7 (GND) Power window motor DOWN output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
K7-4 (DOWN) - K7-7 (GND) Power window motor DOWN output Ignition switch ON, rear LH door power window fully closed 11 to 14 V
K7-4 (DOWN) - K7-7 (GND) Power window motor DOWN output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
K7-4 (DOWN) - K7-7 (GND) Power window motor DOWN output Ignition switch ON, rear LH door power window fully open 11 to 14 V
K7-8 (AUTO) - K7-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear LH door power window fully open 11 to 14 V
K7-8 (AUTO) - K7-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
K7-8 (AUTO) - K7-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear LH door power window fully closed 11 to 14 V
K7-8 (AUTO) - K7-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear LH door power window fully closed 11 to 14 V
K7-8 (AUTO) - K7-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
K7-8 (AUTO) - K7-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear LH door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)


B351350N14
3.385,0.208 3.802,0.479 0.417,0.271 3.531,0.26 3.844,0.458 0.313,0.198 10 false K2

a.

Disconnect the K2 rear power window regulator switch assembly (for RH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
K2-7 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the K2 rear power window regulator switch assembly (for RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
K2-5 (UP) - K2-7 (GND) Power window motor UP output Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
K2-5 (UP) - K2-7 (GND) Power window motor UP output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
K2-5 (UP) - K2-7 (GND) Power window motor UP output Ignition switch ON, rear RH door power window fully open 11 to 14 V
K2-5 (UP) - K2-7 (GND) Power window motor UP output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
K2-5 (UP) - K2-7 (GND) Power window motor UP output Ignition switch ON, rear RH door power window fully closed 11 to 14 V
K2-4 (DOWN) - K2-7 (GND) Power window motor DOWN output Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
K2-4 (DOWN) - K2-7 (GND) Power window motor DOWN output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
K2-4 (DOWN) - K2-7 (GND) Power window motor DOWN output Ignition switch ON, rear RH door power window fully closed 11 to 14 V
K2-4 (DOWN) - K2-7 (GND) Power window motor DOWN output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
K2-4 (DOWN) - K2-7 (GND) Power window motor DOWN output Ignition switch ON, rear RH door power window fully open 11 to 14 V
K2-8 (AUTO) - K2-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear RH door power window fully open 11 to 14 V
K2-8 (AUTO) - K2-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
K2-8 (AUTO) - K2-7 (GND) Power window motor AUTO UP output Ignition switch ON, rear RH door power window fully closed 11 to 14 V
K2-8 (AUTO) - K2-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear RH door power window fully closed 11 to 14 V
K2-8 (AUTO) - K2-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
K2-8 (AUTO) - K2-7 (GND) Power window motor AUTO DOWN output Ignition switch ON, rear RH door power window fully open 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)


B562183C01
1.927,0.427 2.323,0.667 0.396,0.24 1.927,0.854 2.323,1.094 0.396,0.24 2.021,0.458 2.344,0.677 0.323,0.219 10 false J24 2.063,0.896 2.385,1.115 0.323,0.219 10 false J8 2.375,0.469 2.698,0.688 0.323,0.219 10 false *A 2.365,0.896 2.688,1.115 0.323,0.219 10 false *B
*A for LHD *B for RHD


a.

Disconnect the J24*1 or J8*2 power window regulator motor assembly (for driver door) connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J24-1 (GND) - Body ground Ground Always Below 1 Ω
J24-2 (B) - Body ground Power supply Always*1 11 to 14 V
Ignition switch off*2

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J8-1 (GND) - Body ground Ground Always Below 1 Ω
J8-2 (B) - Body ground Power supply Always*1 11 to 14 V
Ignition switch off*2

·

*1: for Gasoline Model

·

*2: for HV Model



c.

Reconnect the J24*1 or J8*2 power window regulator motor assembly (for driver door) connector.

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window fully closed 11 to 14 V
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window fully open 11 to 14 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, driver door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window fully closed 11 to 14 V
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, driver door power window fully open 11 to 14 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) not pushed or not pulled 11 to 14 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, driver door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR)


B562183C02
1.927,0.427 2.323,0.667 0.396,0.24 1.927,0.854 2.323,1.094 0.396,0.24 2.063,0.458 2.385,0.677 0.323,0.219 10 false J8 2.042,0.896 2.365,1.115 0.323,0.219 10 false J24 2.375,0.469 2.698,0.688 0.323,0.219 10 false *A 2.365,0.896 2.688,1.115 0.323,0.219 10 false *B
*A for LHD *B for RHD


a.

Disconnect the J8*1 or J24*2 power window regulator motor assembly (for front passenger door) connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J8-1 (GND) - Body ground Ground Always Below 1 Ω
J8-2 (B) - Body ground Power supply Always*1 11 to 14 V
Ignition switch off*2

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J24-1 (GND) - Body ground Ground Always Below 1 Ω
J24-2 (B) - Body ground Power supply Always*1 11 to 14 V
Ignition switch off*2

·

*1: for Gasoline Model

·

*2: for HV Model



c.

Reconnect the J8*1 or J24*2 power window regulator motor assembly (for front passenger door) connector.

·

*1: for LHD

·

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J8-4 (AUTO) - J8-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
J8-4 (AUTO) - J8-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J8-4 (AUTO) - J8-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J8-4 (AUTO) - J8-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J8-4 (AUTO) - J8-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J8-4 (AUTO) - J8-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully open 11 to 14 V
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J8-7 (DOWN) - J8-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window fully open 11 to 14 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J8-10 (UP) - J8-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J24-4 (AUTO) - J24-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
J24-4 (AUTO) - J24-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J24-4 (AUTO) - J24-1 (GND) Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J24-4 (AUTO) - J24-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J24-4 (AUTO) - J24-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J24-4 (AUTO) - J24-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully open 11 to 14 V
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J24-7 (DOWN) - J24-1 (GND) Power window motor DOWN input Ignition switch ON, front passenger door power window fully open 11 to 14 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or not pulled 11 to 14 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J24-10 (UP) - J24-1 (GND) Power window motor UP input Ignition switch ON, front passenger door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR)


B286758N33
2.167,0.75 2.583,1 0.417,0.25 2.271,0.792 2.656,1 0.385,0.208 10 false K9

a.

Disconnect the K9 power window regulator motor assembly (for rear LH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
K9-1 (GND) - Body ground Ground Always Below 1 Ω
K9-2 (B) - Body ground Power supply Always*1 11 to 14 V
Ignition switch off*2

·

*1: for Gasoline Model

·

*2: for HV Model



c.

Reconnect the K9 power window regulator motor assembly (for rear LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
K9-4 (AUTO) - K9-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear LH door power window fully open 11 to 14 V
K9-4 (AUTO) - K9-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
K9-4 (AUTO) - K9-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
K9-4 (AUTO) - K9-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
K9-4 (AUTO) - K9-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
K9-4 (AUTO) - K9-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window fully open 11 to 14 V
K9-7 (DOWN) - K9-1 (GND) Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
K9-7 (DOWN) - K9-1 (GND) Power window motor DOWN input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
K9-7 (DOWN) - K9-1 (GND) Power window motor DOWN input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
K9-7 (DOWN) - K9-1 (GND) Power window motor DOWN input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
K9-7 (DOWN) - K9-1 (GND) Power window motor DOWN input Ignition switch ON, rear LH door power window fully open 11 to 14 V
K9-10 (UP) - K9-1 (GND) Power window motor UP input Ignition switch ON, rear power window regulator switch assembly (for LH door) not pushed or not pulled 11 to 14 V
K9-10 (UP) - K9-1 (GND) Power window motor UP input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
K9-10 (UP) - K9-1 (GND) Power window motor UP input Ignition switch ON, rear LH door power window fully open 11 to 14 V
K9-10 (UP) - K9-1 (GND) Power window motor UP input Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
K9-10 (UP) - K9-1 (GND) Power window motor UP input Ignition switch ON, rear LH door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR)


B562185N01
2.219,0.771 2.615,1.01 0.396,0.24 2.333,0.813 2.646,1.052 0.313,0.24 10 false K4

a.

Disconnect the K4 power window regulator motor assembly (for rear RH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
K4-1 (GND) - Body ground Ground Always Below 1 Ω
K4-2 (B) - Body ground Power supply Always*1 11 to 14 V
Ignition switch off*2

·

*1: for Gasoline Model

·

*2: for HV Model



c.

Reconnect the K4 power window regulator motor assembly (for rear RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
K4-4 (AUTO) - K4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear RH door power window fully open 11 to 14 V
K4-4 (AUTO) - K4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
K4-4 (AUTO) - K4-1 (GND) Power window motor AUTO UP input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
K4-4 (AUTO) - K4-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
K4-4 (AUTO) - K4-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
K4-4 (AUTO) - K4-1 (GND) Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window fully open 11 to 14 V
K4-7 (DOWN) - K4-1 (GND) Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
K4-7 (DOWN) - K4-1 (GND) Power window motor DOWN input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
K4-7 (DOWN) - K4-1 (GND) Power window motor DOWN input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
K4-7 (DOWN) - K4-1 (GND) Power window motor DOWN input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
K4-7 (DOWN) - K4-1 (GND) Power window motor DOWN input Ignition switch ON, rear RH door power window fully open 11 to 14 V
K4-10 (UP) - K4-1 (GND) Power window motor UP input Ignition switch ON, rear power window regulator switch assembly (for RH door) not pushed or not pulled 11 to 14 V
K4-10 (UP) - K4-1 (GND) Power window motor UP input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
K4-10 (UP) - K4-1 (GND) Power window motor UP input Ignition switch ON, rear RH door power window fully open 11 to 14 V
K4-10 (UP) - K4-1 (GND) Power window motor UP input Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
K4-10 (UP) - K4-1 (GND) Power window motor UP input Ignition switch ON, rear RH door power window fully closed 11 to 14 V



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B562186N01
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.292,6.198 5.729,6.448 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 3.469,7.677 3.781,7.875 0.313,0.198 10 false MB 4.292,0.219 4.604,0.417 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false H42 2.052,1.479 2.365,1.677 0.313,0.198 10 false H43 2.052,1.802 2.365,2 0.313,0.198 10 false H44 0.875,1.073 1.188,1.271 0.313,0.198 10 false 4D 0.875,1.656 1.188,1.854 0.313,0.198 10 false 4C 0.885,2 1.198,2.198 0.313,0.198 10 false 4E 0.906,2.25 1.219,2.448 0.313,0.198 10 false 4F 5.854,1.146 6.167,1.344 0.313,0.198 10 false 4B 5.854,1.76 6.167,1.958 0.313,0.198 10 false 4A 1.229,3.281 1.542,3.479 0.313,0.198 10 false H44 3.271,3.25 3.583,3.448 0.313,0.198 10 false H43 5.542,3.24 5.854,3.438 0.313,0.198 10 false H42 1.833,4.604 2.146,4.802 0.313,0.198 10 false 4A 1.24,6.198 1.552,6.396 0.313,0.198 10 false 4C 3.823,6.156 4.135,6.354 0.313,0.198 10 false 4D 5.427,6.219 5.74,6.417 0.313,0.198 10 false 4F 6.448,6.229 6.76,6.427 0.313,0.198 10 false 4E 5.51,4.604 5.823,4.802 0.313,0.198 10 false 4B

a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors connected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H42-19 (GND2) - Body ground Ground Always Below 1 Ω


c.

Reconnect the instrument panel junction block assembly connectors.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground Ground Always Below 1 Ω
MB-31 (BECU) - Body ground Auxiliary battery power supply Always*1 11 to 14 V
Ignition switch off*2
MB-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
MB-30 (ACC) - Body ground ACC power supply Ignition switch off Below 1 V
MB-32 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
MB-32 (IG) - Body ground IG power supply Ignition switch off or ACC Below 1 V

·

*1: for Gasoline Model

·

*2: for HV Model



e.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION


f.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H43-1 (FLCY) - Body ground Front door courtesy light switch (for LH) input Front door LH open Below 1 V
H43-1 (FLCY) - Body ground Front door courtesy light switch (for LH) input Front door LH closed 11 to 14 V
H43-6 (FRCY) - Body ground Front door courtesy light switch (for RH) input Front door RH open Below 1 V
H43-6 (FRCY) - Body ground Front door courtesy light switch (for RH) input Front door RH closed 11 to 14 V
H44-18 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
H44-18 (L2) - Body ground Driver door key-linked lock input Driver door key cylinder not turned 11 to 14 V
H44-17 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
H44-17 (UL3) - Body ground Driver door key-linked unlock input Driver door key cylinder not turned 11 to 14 V