Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU › from 2020.11
RM37A0E _57 Power Source / Network _086882 POWER DISTRIBUTION _0416685 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

After the main body ECU (multiplex network body ECU) has been replaced, the automatic light control system will not operate until the engine is started.



NOTICE:

After the main body ECU (multiplex network body ECU) has been replaced, the automatic light control system will not operate until the engine is started.


PROCEDURE

Hide 1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for LHD)

NOTICE:
·

Make sure that the connecting surfaces are free of foreign matter.

·

Do not touch the main body ECU (multiplex network body ECU) connector.



a.
E430683C01
1.781,1.333 2.531,0.406 true 0.25,2.146 0.563,2.302 0.313,0.156 10 false *a 2.563,0.281 2.875,0.438 0.313,0.156 10 false *b
*a 20°or more
*b Housing Sidewall
V113147

Set in this Direction


Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the instrument panel junction block assembly as shown in the illustration.

HINT:

Make sure to keep the angle at 20° or more as shown in the illustration.



b.
E430684C01
1.51,1.469 2.021,0.51 true 2.063,0.375 2.375,0.531 0.313,0.156 10 false *a
*a Housing Sidewall
V113147

Slide in this Direction


Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the 2 guides.


c.
E430685C01
2.115,0.833 2.531,0.417 true 2.563,0.313 2.875,0.469 0.313,0.156 10 false *a
*a Side A
V113147

Install in this Direction


While keeping the main body ECU (multiplex network body ECU) in contact with side A of the instrument panel junction block assembly (axis of rotation), lower it as shown in the illustration.


d.
E458443C01
1.052,3 1.417,3 true 0.688,2.958 0.875,2.958 true 1.448,2.896 1.76,3.052 0.313,0.156 10 false *1 0.49,2.885 0.802,3.042 0.313,0.156 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100155

Push Area


Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).

NOTICE:
·

Make sure to press only the push area.

·

Confirm the engagement of the main body ECU (multiplex network body ECU) and instrument panel junction block assembly by listening for the click sound of the lock engaging.



HINT:

If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and instrument panel junction block assembly are flush.



Hide 2.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)

a.
E430679C01
0,0 0,0 false
V113147

Install in this Direction


Connect the 2 connectors and push down the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



b.

Engage the clamp.


c.

Engage the clamp.


d.

Install the instrument panel junction block assembly with main body ECU with the 2 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Engage the 2 guides.


f.
E430675C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws as shown in the illustration.


g.
E430673C01
0,0 0,0 false
V113147

Install in this Direction


Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



h.

Engage the 3 clamps.


i.

Connect each connector.


Hide 82878 3.INSTALL ECU INTEGRATION BOX LH (for LHD)

Hide 55308B 4.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD)

Hide 5.INSTALL INSTRUMENT PANEL SAFETY PAD (for LHD)

Hide 6.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for RHD)

NOTICE:
·

Make sure that the connecting surfaces are free of foreign matter.

·

Do not touch the main body ECU (multiplex network body ECU) connector.



a.
E455768C01
1.927,1.115 2.469,0.729 true 0.458,2 0.771,2.156 0.313,0.156 10 false *a 2.5,0.615 2.969,1.094 0.469,0.479 10 false *b
*a 20°or more
*b Housing Sidewall
V113147

Set in this Direction


Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the instrument panel junction block assembly as shown in the illustration.

HINT:

Make sure to keep the angle at 20° or more as shown in the illustration.



b.
E455769C01
1.083,1.396 0.583,1 true 0.417,0.875 0.729,1.031 0.313,0.156 10 false *a
*a Housing Sidewall
V113147

Slide in this Direction


Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the 2 guides.


c.
E455770C01
2.156,0.802 2.583,0.552 true 2.615,0.458 2.948,0.677 0.333,0.219 10 false *a
*a Side A
V113147

Install in this Direction


While keeping the main body ECU (multiplex network body ECU) in contact with side A of the instrument panel junction block assembly (axis of rotation), lower it as shown in the illustration.


d.
E455771C01
0.708,2.531 0.958,2.531 true 0.323,2.479 0.604,2.479 true 1.021,2.49 1.333,2.646 0.313,0.156 10 false *1 0.135,2.406 0.448,2.563 0.313,0.156 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100155

Push Area


Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).

NOTICE:
·

Make sure to press only the push area.

·

Confirm the engagement of the main body ECU (multiplex network body ECU) and instrument panel junction block assembly by listening for the click sound of the lock engaging.



HINT:

If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and instrument panel junction block assembly are flush.



Hide 82673C 7.INSTALL JUNCTION BLOCK BRACKET (for RHD)

a.

Engage the 2 claws to install the junction block bracket.

E455764


Hide 8.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)

a.

Engage the 4 claws as shown in the illustration.

E455762C01
0,0 0,0 false
V113147

Install in this Direction - -



b.
E455760C01
0,0 0,0 false
V113147

Install in this Direction


Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



c.

Engage the 3 clamps.


d.

Install the instrument panel junction block assembly with main body ECU with the bolt and nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Engage the clamp.


f.

Connect the 3 connectors.


g.

Engage the clamp.


h.

Connect each connector.


i.
E458028C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clamp.


j.

Connect the 2 connectors and raise the 2 lock levers to engage the 2 claws and lock the 2 connectors as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



Hide 55303B 9.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure for the RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION


Hide 55607 10.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

HINT:

Use the same procedure for the RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION


Hide 55436A 11.INSTALL INSTRUMENT PANEL FINISH END PANEL LH (for RHD)

HINT:

Use the same procedure for the RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION


Hide 62312B 12.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)

HINT:

Use the same procedure for the RHD and LHD.

Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR OPENING TRIM WEATHERSTRIP>INSTALLATION


Hide 62112A 13.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)

HINT:

Use the same procedure for the RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 67914 14.INSTALL FRONT DOOR SCUFF PLATE LH (for RHD)

HINT:

Use the same procedure for the RHD and LHD.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION