Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › from 2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0416014 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Brake Booster (Skid Control ECU) Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Brake Booster (Skid Control ECU) Communication Stop Mode Communication stop for "Brake Booster" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

No. 1 skid control ECU (brake booster with master cylinder assembly) branch line or connector

·

Power source circuit of No. 1 skid control ECU (brake booster with master cylinder assembly)

·

No. 1 skid control ECU (brake booster with master cylinder assembly) ground circuit

·

No. 1 skid control ECU (brake booster with master cylinder assembly)



WIRING DIAGRAM

C427147E02
5.688,0.333 6.302,0.531 0.615,0.198 10 false CA1H 5.688,0.906 6.302,1.104 0.615,0.198 10 false CA1L 5.677,1.865 6.292,2.063 0.615,0.198 10 false CA2H 5.688,2.458 6.302,2.656 0.615,0.198 10 false CA2L 5.656,3.365 6.271,3.563 0.615,0.198 10 false +BI1 5.677,4.052 6.292,4.25 0.615,0.198 10 false IG1 5.677,4.771 6.292,4.969 0.615,0.198 10 false IG2 5.677,5.521 6.292,5.719 0.615,0.198 10 false GND1 5.375,0.219 5.781,0.531 0.406,0.313 10 false 38 5.375,0.813 5.781,1.125 0.406,0.313 10 false 39 5.396,1.75 5.802,2.063 0.406,0.313 10 false 35 5.385,2.344 5.792,2.656 0.406,0.313 10 false 36 5.375,3.24 5.781,3.552 0.406,0.313 10 false 14 5.385,3.938 5.792,4.25 0.406,0.313 10 false 31 5.375,4.667 5.781,4.979 0.406,0.313 10 false 42 5.385,5.396 5.792,5.708 0.406,0.313 10 false 28 0.406,1.198 2.948,1.615 2.542,0.417 10 false No. 2 Global CAN Junction Connector*1 0.427,2.75 2.948,3.031 2.521,0.281 10 false No. 1 Global CAN Junction Connector 4.313,6.125 4.875,6.49 0.563,0.365 10 false A44 0.104,2.75 0.667,3.115 0.563,0.365 10 false A77 1.719,1.76 2.125,2.073 0.406,0.313 10 false 2 1.677,2.344 2.083,2.656 0.406,0.313 10 false 13 0.104,1.198 0.667,1.563 0.563,0.365 10 false H90 1.74,0.792 2.146,1.104 0.406,0.313 10 false 8*2 4.625,6.115 7.042,6.656 2.417,0.542 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.99,3.219 4.813,3.458 0.823,0.24 10 false ABS NO. 3 3.844,3.917 4.979,4.229 1.135,0.313 10 false ECU-IG1 NO. 2 3.854,4.646 4.979,4.896 1.125,0.25 10 false ECU-IG2 NO. 3 1.656,3.333 3.865,3.656 2.208,0.323 10 false from Auxiliary Battery 1.646,4.042 3.854,4.365 2.208,0.323 10 false from IG1-NO. 1 Relay 1.667,4.781 3.875,5.104 2.208,0.323 10 false from IG2-NO. 2 Relay 1.688,0.198 2.094,0.51 0.406,0.313 10 false 2*2 1.688,0.042 2.094,0.354 0.406,0.313 10 false 3*1 1.667,0.646 2.073,0.958 0.406,0.313 10 false 13*1 0.104,1.479 0.667,1.844 0.563,0.365 10 false M33 0.406,1.479 2.948,1.896 2.542,0.417 10 false No. 8 Global CAN Junction Connector*2 0.5,5.563 2.708,5.885 2.208,0.323 10 false *1: for LHD 0.5,5.917 2.708,6.24 2.208,0.323 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY) BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.
C427148C01
1.479,0.104 1.896,0.354 0.417,0.25 2.125,2.042 2.125,2.875 2.125,2.875 2.292,2.875 true 2.021,2.042 2.021,3.125 2.021,3.125 2.188,3.125 true 1.729,2.042 1.729,2.875 1.729,2.875 1.563,2.875 true 1.823,2.031 1.823,3.115 1.823,3.115 1.656,3.115 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 1.573,0.156 1.885,0.354 0.313,0.198 10 false A44 1.167,2.792 1.635,3.104 0.469,0.313 10 false CA2H 1.271,3.063 1.74,3.375 0.469,0.313 10 false CA2L 2.26,3.052 2.729,3.333 0.469,0.281 10 false CA1H 2.365,2.792 2.833,3.104 0.469,0.313 10 false CA1L
*a Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A44-38 (CA1H) - A44-39 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A44-35 (CA2H) - A44-36 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 1 SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C427148C02
1.542,0.104 1.958,0.375 0.417,0.271 1.146,2.865 1.313,2.865 1.313,2.865 1.313,2.031 true 2.802,2.844 2.656,2.844 2.656,2.844 2.656,1.927 true 2.438,1.594 2.438,0.823 2.438,0.823 2.583,0.823 true 2.271,2.875 2.438,2.875 2.438,2.875 2.438,2.042 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.646,0.177 2.167,0.469 0.521,0.292 10 false A44 2.667,0.74 3.219,1.021 0.552,0.281 10 false +BI1 0.906,2.792 1.458,3.073 0.552,0.281 10 false IG1 2,2.792 2.552,3.073 0.552,0.281 10 false IG2 2.865,2.75 3.323,3.031 0.458,0.281 10 false GND1
*a Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A44-28 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-14 (+BI1) - Body ground Ignition switch off 11 to 14 V
A44-31 (IG1) - Body ground Ignition switch ON 11 to 14 V
A44-42 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE NO. 1 SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

B

REPLACE NO. 1 SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)