Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model RHD) › from 2020.11
RM37A0E _54 Brake _086869 BRAKE SYSTEM (OTHER) _0449416 BRAKE BOOSTER(for HV Model RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of brake booster with master cylinder assembly
1.

Bleed air

2.

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.

·
C450182C01
3,0.406 2.833,0.406 2.833,0.406 2.833,0.74 false 1.948,0.344 2.448,0.344 false 0.552,1.51 1.052,1.51 false 3.073,1.438 3.073,0.938 true 1.885,1.208 1.885,1.958 true 2.479,0.25 2.938,0.615 0.458,0.365 10 false *a 0.385,1.427 0.75,1.698 0.365,0.271 10 false *b 3,1.448 3.25,1.698 0.25,0.25 10 false *c 3.031,0.323 3.26,0.542 0.229,0.219 10 false *d 1.813,1.979 2.073,2.146 0.26,0.167 10 false *e
*a No. 1 Skid Control ECU
*b No. 1 Reservoir Hose
*c Master Cylinder Push Rod Clevis
*d Boot
*e Reservoir


Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.



PROCEDURE

Hide 1.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

a.

Using the GTS, perform the accumulator pressure zero down operation.

i.

Select "Motor Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 2617

ii.

Perform "Motor Deactivate" according to the display on the GTS.


iii.

Select "ECB Deactivate" on the "ECB Utility" screen.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 2617

iv.

Perform "ECB Deactivate" according to the display on the GTS.


v.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.



vi.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.



vii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL



b.

When the accumulator pressure zero down could not be performed using the GTS.

NOTICE:

If DTCs are output, the accumulator pressure zero down operation may not be complete. In this case, perform the following procedure.


i.
C447841

With the ignition switch off, disconnect the brake booster with accumulator pump connector.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



ii.

Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.


iii.

Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down operation is not complete.



iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL



Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53808A 3.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 4.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 5.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 6.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 7.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 8.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 55704B 9.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 10.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 82111 11.SEPARATE ENGINE ROOM MAIN WIRE

a.
C447874C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the engine room main wire from the brake booster with master cylinder assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.

Disengage the clamp to separate the engine room main wire from the brake booster with master cylinder assembly.


Hide 47235H 12.DISCONNECT NO. 2 RESERVOIR HOSE

a.
C447875

Slide the clip and disconnect the No. 2 reservoir hose from the brake booster with master cylinder assembly.


Hide 47234L 13.DISCONNECT NO. 1 RESERVOIR HOSE

a.
C447876

Slide the clip and disconnect the No. 1 reservoir hose from the brake master cylinder reservoir assembly.


Hide 44571A 14.DISCONNECT NO. 1 BRAKE ACTUATOR HOSE

a.
C447877

Slide the clip and disconnect the No. 1 brake actuator hose from the brake booster with master cylinder assembly.


Hide 15.DISCONNECT BRAKE LINE

a.
C450375C01
2.125,1.396 2.5,0.938 true 1.76,1.635 1.573,1.896 true 1.917,1.521 1.448,1.125 true 2.458,0.76 2.667,0.948 0.208,0.188 10 true *a 1.448,1.927 1.646,2.115 0.198,0.188 10 true *b 1.229,1.01 1.427,1.188 0.198,0.177 10 true *c
*a 1st Chamber of Brake Booster with Master Cylinder Assembly
*b 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Brake Booster with Accumulator Pump Assembly


Use tags or make a memo to identify the places to reconnect the brake lines.


b.
C447878

Using a union nut wrench, disconnect the 3 brake lines from the brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




Hide 47371B 16.REMOVE NO. 6 BRAKE TUBE CLAMP

a.
C447880

Disengage the 4 clamps to remove the No. 6 brake tube clamp.


Hide 17.REMOVE NO. 1 WIRE CLAMP BRACKET

a.
C447879

Disengage the clamp to separate the brake line from the No. 14 brake tube clamp.


b.
C447881

Remove the bolt and No. 1 wire clamp bracket.


Hide 47371P 18.REMOVE NO. 14 BRAKE TUBE CLAMP

a.
C447882

Disengage the clamp and remove the No. 14 brake tube clamp.


Hide 67913 19.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 20.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 55606 21.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 53601 22.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55045 23.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 55446A 24.REMOVE NO. 1 SWITCH HOLE BASE

Hide 73900 25.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 84340 26.REMOVE STOP LIGHT SWITCH ASSEMBLY

Hide 47101A 27.REMOVE BRAKE PEDAL RETURN SPRING

a.
C450180

Remove the brake pedal return spring from the brake pedal support assembly.


Hide 47264A 28.REMOVE PUSH ROD PIN

a.
C445566

Remove the clip and push rod pin.


Hide 47210L 29.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C447883

Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·

Do not apply excessive force to the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.



HINT:

Remove the brake booster with master cylinder assembly while avoiding the brake lines etc.



Hide 44785D 30.REMOVE BRAKE MASTER CYLINDER GASKET

Hide 47234L 31.REMOVE NO. 1 RESERVOIR HOSE

a.
C447884

Disengage the clamp to separate the No. 1 reservoir hose from the brake booster with master cylinder assembly.


b.

Slide the clip and remove the No. 1 reservoir hose.


c.

Remove the 2 clips from the No. 1 reservoir hose.