Home › Steering › STEERING COLUMN › STEERING WHEEL › from 2020.11
RM37A0E _55 Steering _086875 STEERING COLUMN _0418169 STEERING WHEEL A

STEERING COLUMN  STEERING WHEEL  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during steering wheel assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:
·

Do not remove/install the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.


for Gasoline Model:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


for HV Model:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.



PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45130 2.REMOVE HORN BUTTON ASSEMBLY

Hide 3.REMOVE STEERING WHEEL ASSEMBLY

a.

Disconnect each connector.


b.
C431433

Using a 10 mm hexagon socket wrench, remove the steering wheel assembly set bolt.


c.
C431434C01
1.75,1.104 0.771,1.115 0.771,1.115 1.75,1.146 true 0.573,1.031 0.76,1.198 0.188,0.167 10 true *a
*a Matchmark


Put matchmarks on the steering wheel assembly and steering main shaft.


d.

Temporarily install the steering wheel assembly set bolt.

NOTICE:

Do not overtighten the steering wheel assembly set bolt.



e.
C431435C01
0.51,0.844 1.604,0.844 true 0.5,1.281 1.042,1.281 true 3.021,3.688 3.24,3.906 0.219,0.219 10 false *a 0.844,4.094 1.156,4.25 0.313,0.156 10 false *b 0.229,0.76 0.563,0.938 0.333,0.177 10 false SST 0.208,1.208 0.542,1.385 0.333,0.177 10 false SST
*a Turn
*b Hold


Using SST, separate the steering wheel assembly.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031, 09957-04010)
09950-60010  (09951-00330)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.



f.

Remove the steering wheel assembly set bolt and steering wheel assembly.


Hide 84250A 4.REMOVE STEERING PAD SWITCH ASSEMBLY

Hide 5.REMOVE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) (w/ Shift Paddle Switch)