Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE › from 2020.11
RM37A0E _52 Drivetrain _094409 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0449678 TRANSMISSION WIRE A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 12361 1.REMOVE FRONT ENGINE MOUNTING INSULATOR

Hide 53737B 2.REMOVE FRONT FENDER APRON SEAL LH

Hide 3.DRAIN AUTOMATIC TRANSAXLE FLUID

a.
C420751

Remove the refill plug and gasket from the automatic transaxle case sub-assembly.


b.
C420752

Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing.


c.
C420753C01
2.75,0.917 2.854,0.917 false 2.583,0.813 2.792,1.01 0.208,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid.


d.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


e.

Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.



f.

Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.



Hide 32942 4.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

a.
C426629

Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.


Hide 32901C 5.REMOVE OIL COOLER UNION SUB-ASSEMBLY

a.
C426632C01
2.823,2.865 2.698,3.094 2.698,3.094 2.583,2.875 true 2.26,3.073 2.365,2.833 false 2.177,3.094 2.417,3.313 0.24,0.219 10 false *1 2.646,3.104 2.958,3.26 0.313,0.156 10 false *2
*1 Oil Cooler Union Bolt
*2 Gasket


Remove the bolt, oil cooler union bolt, 2 gaskets and oil cooler union sub-assembly from the automatic transaxle case sub-assembly.


Hide 35151F 6.REMOVE TRANSMISSION CASE SIDE COVER

a.
C420748

Remove the 10 bolts and transmission case side cover from the automatic transaxle case sub-assembly.


Hide 82125J 7.REMOVE TRANSMISSION WIRE

a.
C365879C01
0.125,0.229 0.438,0.448 0.313,0.219 10 false *a 0.656,3.25 1.031,3.49 0.375,0.24 10 false *b
*a Connector (A)
*b Connector (B)


Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.


b.

Disconnect the 9 solenoid valve connectors.

HINT:
·

Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.

·

Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.




c.
C365875

Disengage the wire harness clamp to disconnect the transmission wire (oil pump with solenoid assembly).


d.
C365876

Disconnect the transmission wire connector.


e.
C365877

Disengage the clamp to disconnect the transmission wire (oil pump with solenoid assembly) from the solenoid lock plate.


f.
C361010

Remove the bolt and temperature sensor clamp and separate the temperature sensor from the transmission valve body assembly.


g.
C365878

Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.


h.
C361015

Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.