Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.11
RM37A0E _51 Engine / Hybrid System _086851 2GR-FKS ENGINE MECHANICAL _0420086 ENGINE ASSEMBLY A

2GR-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

*3: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*4: If the vehicle height has changed due to suspension or tire replacement

*5: When the starter assembly is replaced, "ST relay" must be also replaced

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly
·

Perform reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for UA80E Initialization:(Click here)
for UA80E Registration:(Click here)
for UA80F Initialization:(Click here)
for UA80F Registration:(Click here)
Replacement of ECM
If transaxle compensation code read from ECM:
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


If transaxle compensation code not read from ECM:
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of starter assembly*5 Clear the number of starter operations Stop and Start System (Click here)
Replacement of battery
·

Integrated Current Value Initialization

·

Switch Battery Type


Replacement of automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for UA80E:(Click here)
for UA80F:(Click here)
Replacement of front bumper assembly*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*4
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform "Calibration".


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6. SECURE STEERING WHEEL

Hide 7.REMOVE FRONT WHEELS

Hide 53852B 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

a.
A451574

Remove the 4 screws and front wheel opening extension pad LH.


Hide 53851D 9.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

a.
A451573

Remove the 4 screws and front wheel opening extension pad RH.


Hide 51441 10.REMOVE NO. 1 ENGINE UNDER COVER

a.
A451568C01
0,0 0,0 false
V100135

Bolt
V100136

Screw


Remove the 3 bolts, 2 clips, 8 screws and No. 1 engine under cover.


Hide 51444A 11.REMOVE REAR ENGINE UNDER COVER LH

a.
A451570C01
0,0 0,0 false
V100135

Bolt
V100136

Screw


Remove the bolt, 3 clips, screw and rear engine under cover LH.


Hide 51443C 12.REMOVE REAR ENGINE UNDER COVER RH

a.
A451569C01
0,0 0,0 false
V100135

Bolt
V100136

Screw


Remove the bolt, 3 clips, screw and rear engine under cover RH.


Hide 58166A 13.REMOVE FRONT FLOOR COVER LH

a.
A451572C01
0,0 0,0 false
V100135

Bolt
V100136

Screw


Remove the 4 bolts, 3 clips, 5 screws and front floor cover LH.


Hide 58165C 14.REMOVE FRONT FLOOR COVER RH

a.
A451571C01
0,0 0,0 false
V100135

Bolt
V100136

Screw


Remove the 5 bolts, 3 clips, 3 screws and front floor cover RH.


Hide 53737B 15.REMOVE FRONT FENDER APRON SEAL LH

a.
A451580

Remove the 2 bolts, clip and front fender apron seal LH from the vehicle body.


Hide 53736 16.REMOVE FRONT FENDER APRON SEAL RH

a.
A451581

Remove the 2 bolts, clip and front fender apron seal RH from the vehicle body.


Hide 52119A 17.REMOVE FRONT BUMPER COVER

Hide 18.DRAIN ENGINE COOLANT

Hide 20.DRAIN AUTOMATIC TRANSAXLE FLUID (for 2WD)

Hide 21.DRAIN AUTOMATIC TRANSAXLE FLUID (for AWD)

Hide 22.DRAIN TRANSFER OIL (for AWD)

Hide 11209 23.REMOVE V-BANK COVER SUB-ASSEMBLY

a.
A455069

Hold the rear of the V-bank cover sub-assembly and raise it to disengage the 2 rear clips.


b.

Raise the V-bank cover sub-assembly to disengage the 2 front clips and remove the V-bank cover sub-assembly.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.



Hide 17750A 24.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A451583

Remove the 2 bolts and inlet air cleaner assembly.


Hide 25.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.

for LHD:

i.
A454751C03
2.115,1.104 2.688,1.104 true 2.729,1.01 3.042,1.167 0.313,0.156 10 true *1 0.885,1.177 1.083,1.365 0.198,0.188 10 true *2 1.115,0.563 1.604,0.792 0.49,0.229 10 true *3 (*A)
*A for LHD
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Ventilation Hose
*3 Vacuum Hose Bracket


Remove the vacuum hose bracket from the air cleaner hose.



b.

Disengage the 2 clamps to disconnect the No. 1 fuel vapor feed hose from the air cleaner hose.


c.

Slide the clip and disconnect the No. 2 ventilation hose from the air cleaner hose.


d.
A451585

Loosen the hose clamp.


e.
A451586C01
1.281,3.354 1.729,4.083 1.729,4.083 1.729,3.583 true 0.802,4.281 0.802,4.073 true 0.729,4.292 1.042,4.49 0.313,0.198 10 false *a 1.698,4.146 2.01,4.344 0.313,0.198 10 false *a
*a Pin


Disconnect the mass air flow meter sub-assembly connector.


f.

Disengage the 2 wire harness clamps.


g.

Disconnect the vacuum hose from the air cleaner hose.


h.

Disengage the 3 pins and remove the air cleaner assembly with air cleaner hose.

NOTICE:

Make sure the air cleaner support remains attached to the vehicle body.



Hide 82111 27.DISCONNECT ENGINE ROOM MAIN WIRE

a.
A407936

Remove the nut and disconnect the engine wire with engine room main wire from the positive (+) battery terminal.


Hide 82121 28.DISCONNECT ENGINE WIRE

a.
A451587C02
0.156,0.177 0.469,0.417 0.313,0.24 12 true *A 0.146,2.448 0.458,2.688 0.313,0.24 12 true *B
*A w/ Stop and Start System
*B w/o Stop and Start System


Remove the nut and disconnect the engine wire from the negative (-) battery terminal.


Hide 29.REMOVE BATTERY

Hide 74404B 30.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A451589

Disengage the 5 clamps from the battery clamp sub-assembly.


b.

Remove the 3 bolts and battery clamp sub-assembly.


Hide 33820B 31.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C426637C01
1.677,2.344 1.917,2 1.917,2 2.083,2 false 2.115,1.875 2.438,2.083 0.323,0.208 10 false *a 2.969,3.146 3.229,3.365 0.26,0.219 10 false *b 3.146,0.729 3.344,0.958 0.198,0.229 10 true *c
*a Clip (A)
*b 45° to 60°
*c Clip (B)


While disengaging the clip (A) as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip (A).


b.

Remove the clip (B) and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


Hide 23826 32.DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

a.
A451592

Slide the clip and disconnect the No. 1 fuel vapor feed hose from the purge valve (purge VSV).


Hide 44778 33.DISCONNECT CONNECTOR TO CHECK VALVE HOSE

a.

for LHD:

i.
A451593

Slide the clip and disconnect the connector to check valve hose from the brake booster assembly.



b.

for RHD:

i.
A480769

Slide the clip and disconnect the connector to check valve hose from the brake booster assembly.



Hide 16572D 34.DISCONNECT NO. 2 RADIATOR HOSE

a.
A451594

Slide the clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 35.SEPARATE RADIATOR HOSE SUB-ASSEMBLY

a.
A451595

Slide the clip and disconnect the No. 4 water by-pass hose from the radiator hose sub-assembly.


b.

Slide the clip and disconnect the radiator hose sub-assembly from the water outlet.


c.

Disengage the clamp.


d.

Remove the 2 bolts and separate the radiator hose sub-assembly from the engine assembly.


Hide 87245B 36.DISCONNECT INLET HEATER WATER HOSE B

a.
A451596

Disengage the 2 clamps.


b.

Slide the clip and disconnect the inlet heater water hose B from the water outlet.


Hide 16260 37.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

a.
A451597C01
1.406,1.302 1.563,1.302 1.563,1.302 2.083,0.875 true 1.146,1.177 1.365,1.396 0.219,0.219 10 true *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the water by-pass hose assembly from the water hose sub-assembly.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected water hose sub-assembly and water by-pass hose assembly connector with plastic bags to prevent damage and contamination.


Hide 23801F 38.DISCONNECT NO. 1 FUEL HOSE

a.
A451599

Disengage the 2 claws to remove the No. 2 fuel pipe clamp.


b.
A451600

Remove the No. 1 fuel pipe clamp from the fuel tube connector.


c.

Disconnect the No. 1 fuel hose (for Port Injection).

i.
A451601

Disconnect the No. 1 fuel hose from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



d.

Disconnect the No. 1 fuel hose (for Direct Injection).

i.
A451602

Disconnect the No. 1 fuel hose from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 88703 39.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 40.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 82121 41.DISCONNECT ENGINE WIRE

HINT:

After disconnecting the engine wire, secure it with tape or equivalent to keep it out of the way.


a.
A451603

Remove the No. 1 relay block cover from the engine room relay block and junction block assembly.


b.
A451604

Remove the nut from the engine room relay block and junction block assembly.


c.

Disconnect the 5 connectors from the engine room relay block and junction block assembly.


d.

Disengage the 2 clamps.


e.

Using a screwdriver, disengage the claw and disconnect the engine wire from the engine room relay block and junction block assembly.


f.
A451605

Remove the bolt.


g.

Disengage the 2 clamps and disconnect the engine wire from the vehicle body.


h.
A451606

Disengage the 3 clamps.


Hide 32943C 42.DISCONNECT NO. 3 TRANSMISSION OIL COOLER HOSE

a.
A451607

Slide the clip and disconnect the No. 3 transmission oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.


b.

Disengage the clamp.


Hide 32942 43.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

a.
A455082

Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.


Hide 45220 44.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 37100 45.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 11361J 48.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A396416

Remove the 2 bolts and flywheel housing under cover.


Hide 32101A 49.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for 2WD)

Hide 32101A 50.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for AWD)

Hide 52618 51.REMOVE FRONT BUMPER LOWER ABSORBER

Hide 52132A 52.REMOVE NO. 2 FRONT BUMPER REINFORCEMENT

Hide 53.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly with transaxle.




b.
A451609

Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.


c.
A451610

Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the front No. 1 engine mounting bracket LH.


d.
A451611

Remove the bolt and nut and separate the engine mounting insulator LH from the engine mounting bracket sub-assembly LH.


e.
A451612C01
0.844,0.271 1,0.469 0.156,0.198 10 true A 2.302,0.208 2.458,0.406 0.156,0.198 10 true A 1.26,2.51 1.417,2.708 0.156,0.198 10 true B 1.979,2.51 2.135,2.708 0.156,0.198 10 true B 0.542,3.656 0.698,3.854 0.156,0.198 10 true C 0.458,4.26 0.615,4.458 0.156,0.198 10 true C 1.313,3.625 1.469,3.823 0.156,0.198 10 true D 1.906,3.625 2.063,3.823 0.156,0.198 10 true D 2.688,3.729 2.844,3.927 0.156,0.198 10 true C 2.771,4.281 2.927,4.479 0.156,0.198 10 true C
V100135

Bolt
V100136

Nut


Remove the 2 bolts (A), 2 bolts (B), 4 nuts, front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.


f.

Remove the 4 bolts (C), 2 bolts (D), front suspension member brace rear RH and front suspension member brace rear LH from the front frame assembly and vehicle body.


g.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 28100 55.REMOVE STARTER ASSEMBLY

Hide 82121 60.REMOVE ENGINE WIRE

a.

Disconnect all clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 61.INSTALL ENGINE HANGERS

a.
A373557C02
1.104,0.729 1.521,0.729 true 2.688,0.719 3.115,0.719 true 0.021,0.021 0.354,0.271 0.333,0.25 12 true *A 1.677,0.031 2,0.26 0.323,0.229 12 true *B 1.583,0.646 1.896,0.802 0.313,0.156 10 false *1 3.156,0.646 3.406,0.865 0.25,0.219 10 false *2
*A for Bank 1
*B for Bank 2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-31121
No. 2 Engine Hanger 12282-31100
Bolt 90119-A0117



b.

Using an engine sling device and engine lifter, secure the engine assembly with transaxle.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent damage or deformation to the engine hangers or engine assembly.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 51100G 62.REMOVE FRONT FRAME ASSEMBLY

a.
A451613

Remove the bolt and separate the front engine mounting insulator from the front engine mounting bracket.


b.
A451614

Remove the bolt and separate the rear engine mounting insulator from the rear engine mounting bracket sub-assembly.


Hide 12361A 63.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A451615

Remove the 3 nuts and front engine mounting insulator from the front frame assembly.


Hide 12371A 64.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A451616

Remove the 4 nuts and rear engine mounting insulator from the front frame assembly.


Hide 32101 67.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 19315 68.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 69.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 70.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and cylinder head LH.


Hide 12305 71.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A451617

Disengage the 2 clamps.


b.

Remove the bolt, nut and separate the radiator reserve tank assembly.


c.
A451608

Remove the bolt and disconnect the No. 2 earth wire from the engine mounting insulator sub-assembly RH.


d.
A451618

Remove the nut, 2 bolts and engine mounting insulator sub-assembly RH from the engine mounting spacer and vehicle body.


Hide 12341 72.REMOVE ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A451619

Remove the 2 bolts and engine mounting spacer from the vehicle body.


Hide 12304 73.REMOVE ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting bracket sub-assembly LH is necessary.


a.
A451620

Remove the 4 bolts and engine mounting bracket sub-assembly LH from the vehicle body.


Hide 12372A 74.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.