Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION WIRE › from 2020.11
RM37A0E _52 Drivetrain _094409 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0449678 TRANSMISSION WIRE A

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION WIRE  INSTALLATION  


PROCEDURE

Hide 82125J 1.INSTALL TRANSMISSION WIRE

a.
C362373

Coat the O-ring of the transmission wire with Toyota Genuine ATF WS.


b.

Install the transmission wire to the automatic transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Connect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.


d.

Install the temperature sensor to the transmission valve body assembly with the bolt and temperature sensor clamp.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)

NOTICE:
C362643C02
1.688,1.646 1.99,1.833 true 1.083,1.167 1.5,1.333 true 1.969,1.865 2.198,2.031 0.229,0.167 10 true *a 0.823,1.063 1.052,1.219 0.229,0.156 10 true *b
*a Transmission Wire (Temperature Sensor Wire)
*b Transmission Revolution Sensor (NC) Wire


To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, pass the transmission revolution sensor (NC) wire under the transmission wire (temperature sensor wire) as shown in the illustration.



e.

Engage the clamp to connect the transmission wire (oil pump with solenoid assembly) to the solenoid lock plate.


f.

Connect the transmission wire connector.


g.

Engage the wire harness clamp to connect the transmission wire (oil pump with solenoid assembly).


h.
C365880

Connect the 9 solenoid valve connectors as shown in the illustration.

NOTICE:
C365881C01
0,0 0,0 false
V100145

Do not let transmission wire protrude into this area.


·

To prevent it from being pinched between the transmission valve body assembly and the transmission case side cover, do not let the transmission wire ride up over the area shown in the illustration.

·

To prevent it from being pinched between the transmission case side cover and the automatic transaxle case sub-assembly, do not let the transmission wire protrude toward the transmission case side cover installation surface.




i.
C365929

Engage the clamp, and connect the transmission wire to the solenoid lock plate.


Hide 35151F 2.INSTALL TRANSMISSION CASE SIDE COVER

a.
C420747C01
0,0 0,0 false
V100145

Area to be cleaned


Clean the transmission case side cover installation surface of the automatic transaxle case sub-assembly.

NOTICE:

Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly.



b.
C427028

Clean the 3 bolt holes shown in the illustration.


c.
P000601C53
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the bolt (A) and 2 bolts (D).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the bolts immediately after applying adhesive to prevent foreign matter from attaching to them.


HINT:

The bolt (A) and 2 bolts (D) are in the locations shown in the following step.



d.
C420748N01
1.188,1.99 1.365,2.167 0.177,0.177 10 false A 2.604,0.156 2.781,0.333 0.177,0.177 10 false B 0.906,0.646 1.042,0.823 0.135,0.177 10 true D 0.906,1.135 1.042,1.313 0.135,0.177 10 true D 1.167,0.01 1.302,0.188 0.135,0.177 10 true C 1.802,0.01 1.938,0.188 0.135,0.177 10 false C 2.688,0.969 2.823,1.146 0.135,0.177 10 false C 2.635,1.448 2.771,1.625 0.135,0.177 10 false C 2.354,1.896 2.49,2.073 0.135,0.177 10 false C 1.719,2.021 1.896,2.177 0.177,0.156 10 false C

Temporarily install a new transmission case side cover to the automatic transaxle case sub-assembly with the 2 bolts ((A) and (B)).

NOTICE:
·

Bolt (A) is the adhesive-coated bolt.

·

To avoid damaging the gasket, prevent it from contacting the surrounding area during installation procedures.




e.

Temporarily install the 6 bolts (C) and 2 bolts (D).

NOTICE:

Bolts (D) are the adhesive-coated bolts.



f.
C420748N03
1.188,1.99 1.365,2.167 0.177,0.177 10 false 1 2.604,0.156 2.781,0.333 0.177,0.177 10 false 2 0.906,0.646 1.042,0.823 0.135,0.177 10 true 5 0.906,1.135 1.042,1.313 0.135,0.177 10 true 9 1.167,0.01 1.302,0.188 0.135,0.177 10 true 3 1.802,0.01 1.938,0.188 0.135,0.177 10 false 7 2.688,0.969 2.823,1.146 0.135,0.177 10 false 6 2.635,1.448 2.854,1.646 0.219,0.198 10 false 10 2.354,1.896 2.49,2.073 0.135,0.177 10 false 4 1.719,2.021 1.896,2.177 0.177,0.156 10 false 8

Fully tighten the 10 bolts in the order shown in the illustration.

Torque:
Bolt (A) and Bolt (D) : 6.5 N*m (66 kgf*cm, 58 in.*lbf)
Bolt (B) and Bolt (C) : 7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 32901C 3.INSTALL OIL COOLER UNION SUB-ASSEMBLY

a.
C426632C01
2.823,2.865 2.698,3.094 2.698,3.094 2.583,2.875 true 2.26,3.073 2.365,2.833 false 2.177,3.094 2.417,3.313 0.24,0.219 10 false *1 2.646,3.104 2.958,3.26 0.313,0.156 10 false *2
*1 Oil Cooler Union Bolt
*2 Gasket


Pass the oil cooler union sub-assembly through 2 new gaskets and temporarily install it to the automatic transaxle case sub-assembly with the oil cooler union bolt.


b.

Temporarily install the oil cooler union sub-assembly bracket portion to the automatic transaxle case sub-assembly with the bolt.


c.

Fully tighten the oil cooler union bolt.

Torque:
22.6 N*m (230 kgf*cm, 17 ft.*lbf)


d.

Fully tighten the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 32942 4.CONNECT OUTLET NO. 1 OIL COOLER HOSE

a.
C426630C01
1.208,2.896 1.333,3.208 1.333,3.208 1.479,3.208 true 1.323,2.052 1.635,2.208 0.313,0.156 10 false *a 1.385,2.281 1.698,2.438 0.313,0.156 10 false *b 1.51,3.094 1.823,3.25 0.313,0.156 10 false *c 1.917,2.583 2.229,2.74 0.313,0.156 10 false *d 1.917,2.927 2.229,3.083 0.313,0.156 10 false *d
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b 0 to 3 mm (0 to 0.118 in.)
*c Paint Mark (Left Side of Vehicle)
*d 30° (Paint Mark Location)


Connect the outlet No. 1 oil cooler hose to the oil cooler union sub-assembly and slide the clip to secure it.

NOTICE:
·

Make sure to slide the outlet No. 1 oil cooler hose until it contacts the hose stopper of the oil cooler union sub-assembly.

·

Make sure that the paint mark of the outlet No. 1 oil cooler hose is within the location shown in the illustration.




Hide 53737B 6.INSTALL FRONT FENDER APRON SEAL LH

Hide 12361 7.INSTALL FRONT ENGINE MOUNTING INSULATOR