Home › Vehicle Interior › HEATING / AIR CONDITIONING › BLOWER UNIT › from 2020.11
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0417364 BLOWER UNIT A

HEATING / AIR CONDITIONING  BLOWER UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during blower assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Steering sensor* Steering angle setting Parking Assist Monitor System (Click here)
Adjust steering angle Panoramic View Monitor System (Click here)
Steering angle neutral point Parking Assist Monitor System (Click here)
Parking Support Brake System (Click here)
Panoramic View Monitor System (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

Before removing the blower assembly, set the air conditioning to recirculation mode.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Steering sensor* Steering angle setting Parking Assist Monitor System (Click here)
Adjust steering angle Panoramic View Monitor System (Click here)
Steering angle neutral point Parking Assist Monitor System (Click here)
Parking Support Brake System (Click here)
Panoramic View Monitor System (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

Before removing the blower assembly, set the air conditioning to recirculation mode.


PROCEDURE

Hide 87130D 3.REMOVE BLOWER ASSEMBLY

a.

for LHD:

i.
E430648

Disconnect the connector.


ii.

Disengage each guide.


iii.
E430649

Remove the 2 screws.


iv.

Disengage the 2 claws and 2 guides and remove the blower assembly from the air conditioning radiator assembly.



b.

for RHD:

i.
E455714

Disconnect the connector.


ii.

Disengage each guide.


iii.

Remove the 2 screws.

E455715


iv.

Disengage the 2 claws and guide and remove the blower assembly from the air conditioning radiator assembly.