Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT AIR CONDITIONING UNIT (for HV Model) › from 2020.11
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0417361 FRONT AIR CONDITIONING UNIT(for HV Model) A

HEATING / AIR CONDITIONING  FRONT AIR CONDITIONING UNIT(for HV Model)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during air conditioner unit assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Steering sensor* Steering angle setting Parking Assist Monitor System (Click here)
Adjust steering angle Panoramic View Monitor System (Click here)
Steering angle neutral point Parking Assist Monitor System (Click here)
Parking Support Brake System (Click here)
Panoramic View Monitor System (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

Make sure to select face mode before disconnecting the cable from the negative (-) auxiliary battery terminal.


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53808A 4.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 5.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 6.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 7.REMOVE FRONT FENDER SPLASH SHEILD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 53608A 8.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 9.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 55704B 10.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY (for LHD)

Hide 55704B 11.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY (for RHD)

Hide 88707 12.DISCONNECT SUCTION PIPE SUB-ASSEMBLY (w/o Sub-cool Accelerator)

a.
E455719

Remove the bolt and rotate the hook connector as shown in the illustration.


b.
E431227

Disconnect the suction pipe sub-assembly.


c.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88716A 13.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (w/o Sub-cool Accelerator)

a.
E431228

Disconnect the cooler refrigerant liquid pipe A.


b.

Remove the O-ring from the cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88710G 14.DISCONNECT NO. 2 AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY (w/ Sub-cool Accelerator)

a.
E435594

Remove the bolt and rotate the hook connector as shown in the illustration.


b.
E435596

Disconnect the No. 2 air conditioner tube and accessory assembly.


c.

Remove the 2 O-rings from the No. 2 air conditioner tube and accessory assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 87246B 15.DISCONNECT OUTLET HEATER WATER HOSE B

a.
E431222

Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose B.

NOTICE:
·

Do not apply excessive force to the outlet heater water hose B.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245B 16.DISCONNECT INLET HEATER WATER HOSE B

a.
E431224

Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose B.

NOTICE:
·

Do not apply excessive force to the inlet heater water hose B.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 17.REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

Hide 18.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Hide 19.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

Hide 83108 20.REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 87201L 21.REMOVE NO. 4 AIR DUCT SUB-ASSEMBLY

Hide 45250 22.REMOVE STEERING COLUMN ASSEMBLY

Hide 82877 23.REMOVE ECU INTEGRATION BOX RH (for LHD)

Hide 82877 24.REMOVE ECU INTEGRATION BOX RH (for RHD)

Hide 25.REMOVE PARKING ASSIST ECU WITH BRACKET

Hide 89343C 26.REMOVE NO. 1 CLEARANCE WARNING BUZZER (for LHD)

Hide 88625Q 27.REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR

a.
E431641

Disconnect the connector and aspirator to remove the cooler (room temp. sensor) thermistor.


Hide 87212F 30.REMOVE REAR NO. 2 AIR DUCT

a.
E431645

Disengage the 4 guides and turn back the front floor carpet assembly as shown in the illustration.


b.
E431647

Remove the clip.


c.

Disengage the 4 claws and remove the rear No. 2 air duct.


Hide 87212 31.REMOVE REAR NO. 1 AIR DUCT

a.
E431648

Disengage the 4 claws and remove the rear No. 1 air duct.


Hide 87212H 32.REMOVE REAR NO. 4 AIR DUCT

a.
E431649

Disengage the 4 guides and turn back the front floor carpet assembly as shown in the illustration.


b.
E431651

Remove the clip.


c.

Disengage the 4 claws and remove the rear No. 4 air duct.


Hide 87212G 33.REMOVE REAR NO. 3 AIR DUCT

a.
E431652

Disengage the 4 claws and remove the rear No. 3 air duct.


Hide 55215D 34.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
E431653

Remove the No. 3 dash panel insulator pad.

NOTICE:

If the No. 3 dash panel insulator pad is damaged, replace it with a new one.



Hide 55837C 35.REMOVE CENTER HEATER TO REGISTER SUB DUCT

a.
E431654

Remove the 2 screws.


b.

Disengage the guide to remove the center heater to register sub duct.


Hide 36.DISCONNECT INSTRUMENT PANEL WIRE (for LHD)

a.

Disconnect the connector.

E456767C02
0.406,0.271 0.906,0.49 true 4.115,0.5 4.583,0.281 true 5.854,3.292 6.063,3.219 true 0.813,5.438 0.813,5.219 true 5.781,3.958 6.313,3.667 true 6.667,3.125 6.875,3.052 true 0.219,0.167 0.406,0.375 0.188,0.208 10 true *a 4.594,0.167 4.781,0.375 0.188,0.208 10 true *a 5.573,3.854 5.76,4.063 0.188,0.208 10 true *a 0.75,5.438 0.938,5.646 0.188,0.208 10 true *a 5.625,3.208 5.813,3.417 0.188,0.208 10 true *b 6.885,2.938 7.135,3.177 0.25,0.24 12 true *A
*A w/ Airbag Cut Off Switch - -
*a Earth Wire *b Connector Holder
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Connector
V100138

Nut



b.

Remove the 4 bolts (A) and disconnect the 4 earth wires.


c.

Remove the 2 nuts.


d.

Remove the bolt (B) and disconnect the connector holder.


e.

Disengage each clamp.


f.
E434825C01
1.677,2.938 2.5,2.344 true 1.469,2.833 1.781,2.99 0.313,0.156 10 false *a
*a Earth Wire
V100135

Connector
V100136

Bolt


Disconnect the 2 connectors.


g.

Disengage each clamp.


h.

Remove the bolt and disconnect the earth wire.


Hide 37.DISCONNECT INSTRUMENT PANEL WIRE (for RHD)

a.

Disconnect the connector.

E455723C01
0.573,7.24 1.104,7.354 1.104,7.354 0.833,6.708 true 5.729,4.271 6.74,3.563 6.74,3.563 6.646,3.906 true 5.99,4.708 6.396,4.344 true 1.198,6.583 1.938,6.365 true 3.417,0.469 3.969,1.313 true 1.115,7.25 1.396,7.469 0.281,0.219 12 true *A 5.792,4.625 5.979,4.802 0.188,0.177 10 true *b 6.76,3.448 7.073,3.604 0.313,0.156 10 false *a 1.948,6.25 2.135,6.427 0.188,0.177 9 true *a 3.25,0.375 3.438,0.552 0.188,0.177 9 false *a
*A w/ Airbag Cut Off Switch - -
*a Earth Wire *b Connector Holder
V100135

Bolt
V100136

Nut (A)
V100137

Nut (B)
V100138

Connector



b.

Remove the 4 bolts and disconnect the 4 earth wires.


c.

Remove the 2 nuts (A).


d.

Remove the nut (B) and disconnect the connector holder.


e.

Disengage each clamp.


f.
E455724C01
1.26,3.01 0.417,2.229 true 1.271,2.927 1.469,3.125 0.198,0.198 10 true *a
*a Earth Wire
V100135

Connector
V100136

Bolt


Disconnect the 2 connectors.


g.

Disengage each clamp.


h.

Remove the bolt and disconnect the earth wire.


Hide 55306A 38.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E431657C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Nut


Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.


Hide 55307C 39.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
E431658C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Nut


Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.


Hide 40.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.
E431659

Remove the clip.


b.

Disconnect the drain cooler hose.

NOTICE:

If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress.



c.
E431661

Remove the cooler unit drain hose grommet.


d.
E431663

Remove the 2 hole plugs.


e.
E431664

Remove the 3 bolts.


f.

Remove the 4 bolts (A).

E431665C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)
V100137

Nut - -



g.

Remove the bolt (B) and disconnect the brake pedal assembly.


h.

Remove the nut.


i.

for LHD:

i.

Disengage each clamp.

E431666C01
0,0 0,0 false
V113147

Remove in this Direction - -



ii.

Disconnect the 4 connectors.


iii.

Remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.



j.

for RHD:

i.

Disengage each clamp.

E455725C01
0,0 0,0 false
V113147

Remove in this Direction - -



ii.

Disconnect the 4 connectors.


iii.

Remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.



Hide 55835A 41.REMOVE CENTER HEATER TO REGISTER DUCT

a.
E431670

Disengage the 6 claws to remove the center heater to register duct.


Hide 42.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and the air conditioner unit assembly from the instrument panel reinforcement assembly.

E431671