Home › Power Source / Network › 2GR-FKS (BATTERY / CHARGING) › CHARGING SYSTEM (w/ Stop And Start System) › from 2020.11
RM37A0E _57 Power Source / Network _086881 2GR-FKS BATTERY / CHARGING _0452458 CHARGING SYSTEM(w/ Stop And Start System) C

2GR-FKS BATTERY / CHARGING  CHARGING SYSTEM(w/ Stop And Start System)  P058A01  Battery Monitor Module General Electrical Failure  


DESCRIPTION

The battery state sensor assembly detects the voltage, current and temperature of the battery. The battery state sensor assembly calculates State of Charge (SOC) based on the voltage and current of the battery and sends it to the ECM. Based on the signals received, the ECM adjusts the charging voltage of the generator assembly.

The battery state sensor assembly calculates the battery temperature based on changes in resistance of a built-in thermistor and sends it to the ECM. The ECM reduces the amount of charging current based on this signal in order to protect the battery.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P058A01 Battery Monitor Module General Electrical Failure Any of the following conditions is met with the ignition switch to ON. (1 trip detection logic):
·

Current is 999.939 A or more, or -1000 A or less for 3.2 seconds or more.

·

The difference between the maximum and minimum current is 0.0305 A or less for 100 seconds or more.

·

A current detection circuit malfunction signal is received.

·

The battery temperature is 105°C (221°F) or more or -40°C (-40°F) or less for 3.2 seconds or more.

·

A temperature detection circuit malfunction signal is received.

·

Voltage is 15.98 V or more, or 6.0 V or less for 3.2 seconds or more.

·

A voltage detection circuit malfunction signal is received.

·

A writing error occurs in the battery state sensor internal memory (battery identification data).


·

Battery state sensor assembly

·

Battery

·

Wire harness or connector


Charge warning is not displayed DTC stored SAE Code: P058A

WIRING DIAGRAM

A426248E17
0.927,2.271 1.844,2.469 0.917,0.198 10 false Battery 0.75,1.323 1.365,1.521 0.615,0.198 10 false FL MAIN 1.531,0.833 2.302,1.031 0.771,0.198 10 false BATT-S 3.01,0.667 3.323,0.865 0.313,0.198 10 false +B 4.083,0.667 4.542,0.865 0.458,0.198 10 false LIN 5.5,0.656 6.115,0.854 0.615,0.198 10 false LIN 2.656,3.323 4.76,3.531 2.104,0.208 10 false : LIN Communication Line 2.854,1.177 3.313,1.375 0.458,0.198 10 false A51 2.833,1.333 5.125,1.531 2.292,0.198 10 false Battery State Sensor Assembly 5.729,2.854 6.188,3.052 0.458,0.198 10 false C54 5.74,3.021 6.25,3.313 0.51,0.292 10 false ECM 2.74,0.51 2.896,0.708 0.156,0.198 10 false 1 4.406,0.458 4.563,0.656 0.156,0.198 10 false 2 5.156,0.469 5.469,0.667 0.313,0.198 10 false 135

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When P162B87 (Lost Communication with Battery Monitor Module Missing Message) is output at the same time, perform the inspection for P162B87 (Lost Communication with Battery Monitor Module Missing Message) first.

Click herePower Source / Network>2GR-FKS (BATTERY / CHARGING)>CHARGING SYSTEM (w/ Stop And Start System)>P162B87



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION
a.

Check installation condition of the battery state sensor assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK CHARGING SYSTEM

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK CHARGING SYSTEM

OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the A51 battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



d.
A417367C15
1.521,0.125 1.938,0.344 0.417,0.219 0.667,1.75 0.667,1.5 0.667,1.5 1.552,1.146 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.625,0.167 1.979,0.354 0.354,0.188 10 false A51 0.615,1.792 0.927,1.99 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A51-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - BATTERY STATE SENSOR ASSEMBLY)