Home › Power Source / Network › 2GR-FKS (BATTERY / CHARGING) › CHARGING SYSTEM (w/ Stop And Start System) › from 2020.11
RM37A0E _57 Power Source / Network _086881 2GR-FKS BATTERY / CHARGING _0452458 CHARGING SYSTEM(w/ Stop And Start System) C

2GR-FKS BATTERY / CHARGING  CHARGING SYSTEM(w/ Stop And Start System)  P162B87  Lost Communication with Battery Monitor Module Missing Message  


DESCRIPTION

The ECM communicates with the battery state sensor assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P162B87 Lost Communication with Battery Monitor Module Missing Message Battery state sensor assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch to ON.
(1 trip detection logic)
·

Wire harness or connector

·

Battery state sensor assembly

·

ECM


Charge warning is not displayed DTC stored SAE Code: P162B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Make sure to perform the necessary procedures (adjustment, calibration, initialization, or registration) after parts related to the charging system have been removed/installed or replaced.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION
a.

Check installation condition of the battery state sensor assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK CHARGING SYSTEM

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK CHARGING SYSTEM

OK

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)
a.

Disconnect the C54 ECM connector.


b.

Disconnect the A51 battery state sensor assembly connector.


c.

Disconnect the C57 generator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-135 (LIN) - A51-2 (LIN) Always Below 1 Ω
C54-135 (LIN), A51-2 (LIN) or C57-2 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the A51 battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



d.
A417367C16
1.521,0.125 1.938,0.344 0.417,0.219 0.667,1.75 0.667,1.5 0.667,1.5 1.552,1.146 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.615,0.167 1.927,0.365 0.313,0.198 10 false A51 0.615,1.792 0.927,1.99 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A51-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CLEAR DTCS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - BATTERY STATE SENSOR ASSEMBLY)

5.CLEAR DTCS
a.

Check for DTCs, and then write them down.

Powertrain > Engine > Trouble Codes
50001 372

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCS
6.CHECK FOR DTCS
a.

Allow the engine to idle for approximately 17 minutes or more.


b.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Only DTC P162B87 is output. A
DTC P161A87 and P162B87 are output. B
DTCs are not output. C



A

B

C