Home › Vehicle Interior › SEAT › FRONT POWER SEAT MOTOR ASSEMBLY › from 2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0416493 FRONT POWER SEAT MOTOR ASSEMBLY A

SEAT  FRONT POWER SEAT MOTOR ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front power seat motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Reclining motor (separate type front seatback spring assembly (driver seat))*

·

Slide motor (separate type front seat cushion spring assembly (driver seat))*

·

Front vertical motor (power seat tilt motor assembly (driver seat))*

·

Lifter motor (power seat lifter motor assembly (driver seat))*


Initialize position control ECU Front Power Seat Control System (w/ Memory) (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
·

Reclining motor (separate type front seatback spring assembly (driver seat))*

·

Slide motor (separate type front seat cushion spring assembly (driver seat))*

·

Front vertical motor (power seat tilt motor assembly (driver seat))*

·

Lifter motor (power seat lifter motor assembly (driver seat))*


Initialize position control ECU Front Power Seat Control System (w/ Memory) (Click here)

CAUTION:
B543257

Wear protective gloves. Sharp areas on the parts may injure your hands.


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 71074S 3.DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER

Hide 71868N 4.REMOVE FRONT SEAT FRONT CUSHION SHIELD

Hide 71812D 5.REMOVE FRONT SEAT CUSHION SHIELD

Hide 71862 6.REMOVE FRONT SEAT INNER CUSHION SHIELD

Hide 7.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

Hide 8.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

Hide 71876 9.REMOVE RECLINING ADJUSTER INSIDE COVER LH (for LH Side)

Hide 11.REMOVE POWER SEAT LIFTER MOTOR ASSEMBLY

a.

Remove the power seat lifter motor assembly.

i.
B564759

Remove the 3 nuts and front seat adjuster plate.


ii.
B564760

Remove the vertical adjuster spacer.


iii.
B564761

Remove the front seat vertical housing sub-assembly.



Hide 12.REMOVE POWER SEAT TILT MOTOR ASSEMBLY

a.
B564762

Remove the 3 bolts and power seat tilt motor assembly.