Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Gasoline Model with Manual Air Conditioning System) › from 2020.11
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0453069 AIR CONDITIONING SYSTEM(for Gasoline Model with Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Gasoline Model with Manual Air Conditioning System)  B1422  Compressor Lock  


DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. If the difference becomes excessively large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnet clutch assembly off.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1422 Compressor Lock Open or short in A/C lock sensor circuit
·

Cooler compressor assembly

·

Harness or connector

·

Air conditioning amplifier assembly


Memorized
(3 seconds or more)*

*: The air conditioning amplifier assembly stores the DTC if the malfunction has occurred for the period of time indicated in the brackets.

WIRING DIAGRAM

E432278E01
2.573,1.656 3,1.854 0.427,0.198 10 false SSR+ 2.573,2.156 3,2.354 0.427,0.198 10 false SSR- 3.063,1.667 3.49,1.865 0.427,0.198 10 false 1 3.063,2.156 3.49,2.354 0.427,0.198 10 false 2 1.063,2.75 3.49,3 2.427,0.25 10 false Cooler Compressor Assembly 1.063,2.594 1.375,2.781 0.313,0.188 10 false C60 4.906,1.792 5.219,1.979 0.313,0.188 10 false H63 5.052,2.865 6.594,3.219 1.542,0.354 10 false Air Conditioning Amplifier Assembly 4.958,2.073 5.24,2.271 0.281,0.198 10 false 14 4.958,1.573 5.219,1.76 0.26,0.188 10 false 12 5.323,2.156 5.677,2.344 0.354,0.188 10 false SG-2 5.313,1.677 5.719,1.875 0.406,0.198 10 false LOCK 5.948,1.781 6.156,1.979 0.208,0.198 10 false IC 2.5,1.104 2.906,1.302 0.406,0.198 10 false ECM 0.552,3.354 2.406,3.583 1.854,0.229 10 false : CAN Communication Line 4.917,2.281 5.229,2.469 0.313,0.188 10 false H63

CAUTION / NOTICE / HINT

NOTICE:
·

The air conditioning system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the air conditioning system after confirming that the communication systems are functioning properly.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

ECM malfunctions can affect the storage of this DTC. Therefore, check all SFI system DTCs and confirm that the system is normal before performing the following inspection.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

After replacing the air conditioning amplifier assembly, make sure to perform Initialization Servo Motor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model with Manual Air Conditioning System)>INITIALIZATION



PROCEDURE

1.INSPECT COOLER COMPRESSOR ASSEMBLY

OK

2.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the H63 air conditioning amplifier assembly connector.


b.

Disconnect the C60 cooler compressor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-1 (SSR+) - H63-12 (LOCK) Always Below 1 Ω
C60-2 (SSR-) - H63-14 (SG-2) Always Below 1 Ω
C60-1 (SSR+) or H63-12 (LOCK) - Other terminals and body ground Always 10 kΩ or higher
C60-2 (SSR-) or H63-14 (SG-2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR