Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for HV Model) › from 2020.11
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0420832 AIR CONDITIONING SYSTEM(for HV Model) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for HV Model)  Weak Blower Output  


DESCRIPTION

If the airflow from the registers is weak regardless of the blower speed setting displayed on the air conditioning control assembly, the following factors may be the cause.

Symptom Factor
·

Airflow volume is constantly low

·

Airflow volume sometimes becomes low


for Front air conditioning unit:
·

ECO mode control of air conditioning system is enabled

·

Blower motor with fan sub-assembly malfunction

·

Clogged clean air filter

·

Clogged No. 1 cooler evaporator sub-assembly or heater radiator unit sub-assembly fins

·

Evaporator temp. sensor (No. 1 cooler thermistor) not connected properly

·

Aspirator pipe not connected properly


for Rear air conditioning unit:
·

ECO mode control of air conditioning system is enabled

·

Rear blower motor with fan sub-assembly malfunction

·

Clogged rear evaporator sub-assembly



PROCEDURE

1.CHECK MALFUNCTIONING AREA
a.

Confirm the area where the blower airflow volume is low.


Result:
Result Proceed to
Front air conditioning unit A
Rear air conditioning unit B



A

2.CHECK AIR CONDITIONING SYSTEM

B

7.CHECK AIR CONDITIONING SYSTEM
2.CHECK AIR CONDITIONING SYSTEM
a.

Operate the blower switch with the following conditions met and check that the airflow volume changes.

Blower Speed Condition
LO → HI
·

Temperature setting: MAX COLD

·

Air outlet mode: FACE

·

A/C switch: Off



OK:

Airflow volume increases.



Result:
Proceed to
OK
NG



OK

3.CHECK ECO MODE SETTING

NG

3.CHECK ECO MODE SETTING
a.

Confirm that ECO drive mode is set to off.

HINT:

When the ECO drive mode is set to ON, the air conditioning amplifier assembly performs minimal air conditioning control in order to promote the improvement of fuel economy. Ensure that the customer understands that the airflow volume will be decreased compared to normal operation.

Control Control Summary
Air Volume Control Sets the blower level to less.



b.

w/ Toyota Multi Operation Touch System:

i.

Confirm that ECO HEAT/COOL switch (multi-display assembly) is set to off.



Result:
Proceed to
NEXT



NEXT

4.CHECK CLEAN AIR FILTER
4.CHECK CLEAN AIR FILTER
a.

Visually check the clean air filter.

OK:

The clean air filter is not dirty or clogging.



Result:
Proceed to
OK
NG



OK

5.CHECK EVAPORATOR TEMP. SENSOR (NO. 1 COOLER THERMISTOR)

NG

5.CHECK EVAPORATOR TEMP. SENSOR (NO. 1 COOLER THERMISTOR)
a.

Check the installation condition of the evaporator temp. sensor (No. 1 cooler thermistor).

OK:

Evaporator temp. sensor (No. 1 cooler thermistor) is installed correctly.



Result:
Proceed to
OK
NG



OK

6.CHECK ASPIRATOR PIPE

NG

REINSTALL EVAPORATOR TEMP. SENSOR (NO. 1 COOLER THERMISTOR)

6.CHECK ASPIRATOR PIPE
a.

Check the installation condition of the aspirator pipe.

OK:

The aspirator pipe is installed correctly.



Result:
Proceed to
OK
NG



OK

REPLACE HEATER RADIATOR UNIT SUB-ASSEMBLY OR NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

NG

7.CHECK AIR CONDITIONING SYSTEM
a.

Operate the blower switch with the following conditions met and check that the airflow volume changes.

Blower Speed Condition
LO → HI
·

Temperature setting: MAX COLD

·

Air outlet mode: FACE

·

A/C switch: Off



OK:

Airflow volume increases.



Result:
Proceed to
OK
NG



OK

8.CHECK ECO MODE SETTING

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Rear Blower Motor Circuit)

8.CHECK ECO MODE SETTING
a.

Confirm that ECO drive mode is set to off.

HINT:

When the ECO drive mode is set to ON, the air conditioning amplifier assembly performs minimal air conditioning control in order to promote the improvement of fuel economy. Ensure that the customer understands that the airflow volume will be decreased compared to normal operation.

Control Control Summary
Air Volume Control Sets the blower level to less.



b.

w/ Toyota Multi Operation Touch System:

i.

Confirm that ECO HEAT/COOL switch (multi-display assembly) is set to off.



Result:
Proceed to
NEXT



NEXT