This DTC is stored when a communication telematics box signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B157213 | Microphone Circuit Open | Current at terminal MCVD exceeds the malfunction threshold for 10 seconds or more while the ignition switch is ON | ·
Telematics transceiver ·
Map light assembly ·
Communication telematics box ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 10 seconds or more.
Turn the GTS on.
Clear the DTCs.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 24 (MICV) - Body ground | Ignition switch ACC | 4 to 6 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H11 telematics transceiver connector.
Disconnect the R17 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H11-8 (MCMD) - R17-1 (MCMD) | Always | Below 1 Ω |
| H11-18 (SP+) - R17-3 (SP+) | Always | Below 1 Ω |
| H11-34 (SP-) - R17-9 (SP-) | Always | Below 1 Ω |
| H11-24 (MICV) - R17-6 (MICV) | Always | Below 1 Ω |
| H11-5 (MCVD) - R17-10 (MIC1) | Always | Below 1 Ω |
| H11-6 (MCI+) - R17-11 (MIC2) | Always | Below 1 Ω |
| H11-7 (MCI-) - R17-5 (MCI-) | Always | Below 1 Ω |
| H11-8 (MCMD) or R17-1 (MCMD) - Body ground | Always | 10 kΩ or higher |
| H11-18 (SP+) or R17-3 (SP+) - Body ground | Always | 10 kΩ or higher |
| H11-34 (SP-) or R17-9 (SP-) - Body ground | Always | 10 kΩ or higher |
| H11-24 (MICV) or R17-6 (MICV) - Body ground | Always | 10 kΩ or higher |
| H11-5 (MCVD) or R17-10 (MIC1) - Body ground | Always | 10 kΩ or higher |
| H11-6 (MCI+) or R17-11 (MIC2) - Body ground | Always | 10 kΩ or higher |
| H11-7 (MCI-) or R17-5 (MCI-) - Body ground | Always | 10 kΩ or higher |
| H11-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly) |
| *b | Component without harness connected
(Communication Telematics Box) |
Disconnect the R17 map light assembly connector.
Disconnect the P communication telematics box connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R17-1 (MCMD) - P-1 (MCMD) | Always | Below 1 Ω |
| R17-3 (SP+) - P-3 (SP+) | Always | Below 1 Ω |
| R17-9 (SP-) - P-8 (SP-) | Always | Below 1 Ω |
| R17-6 (MICV) - P-5 (MICV) | Always | Below 1 Ω |
| R17-10 (MIC1) - P-2 (MIC1+) | Always | Below 1 Ω |
| R17-11 (MIC2) - P-7 (MIC2+) | Always | Below 1 Ω |
| R17-5 (MCI-) - P-4 (MCI-) | Always | Below 1 Ω |
| R17-1 (MCMD) or P-1 (MCMD) - Body ground | Always | 10 kΩ or higher |
| R17-3 (SP+) or P-3 (SP+) - Body ground | Always | 10 kΩ or higher |
| R17-9 (SP-) or P-8 (SP-) - Body ground | Always | 10 kΩ or higher |
| R17-6 (MICV) or P-5 (MICV) - Body ground | Always | 10 kΩ or higher |
| R17-10 (MIC1) or P-2 (MIC1+) - Body ground | Always | 10 kΩ or higher |
| R17-11 (MIC2) or P-7 (MIC2+) - Body ground | Always | 10 kΩ or higher |
| R17-5 (MCI-) or P-4 (MCI-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the communication telematics box with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>COMMUNICATION TELEMATICS BOX>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT