Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Radio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Radio Receiver Assembly Communication Stop Mode Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Radio and display receiver assembly branch line or connector

·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly



WIRING DIAGRAM

C424513E03
0.448,1.458 3.031,1.792 2.583,0.333 10 false No. 6 Global CAN Junction Connector 0.104,1.458 0.573,1.677 0.469,0.219 10 false H95 4.75,5.167 7.135,5.615 2.385,0.448 10 false Radio and Display Receiver Assembly 5.354,0.531 5.823,0.75 0.469,0.219 10 false H2 5.354,1.042 5.823,1.26 0.469,0.219 10 false H2 5.354,3.844 5.823,4.063 0.469,0.219 10 false H2 1.625,0.417 2.094,0.635 0.469,0.219 10 false 4 1.604,0.927 2.073,1.146 0.469,0.219 10 false 15 5.365,0.313 5.833,0.531 0.469,0.219 10 false 13 5.365,0.844 5.833,1.063 0.469,0.219 10 false 14 5.365,1.854 5.833,2.073 0.469,0.219 10 false H1 5.354,2.833 5.823,3.052 0.469,0.219 10 false H1 5.365,4.5 5.833,4.719 0.469,0.219 10 false H1 5.396,1.625 5.865,1.844 0.469,0.219 10 false 4 5.354,2.625 5.823,2.844 0.469,0.219 10 false 15 5.354,3.594 5.823,3.813 0.469,0.219 10 false 19 5.406,4.292 5.875,4.51 0.469,0.219 10 false 1 5.719,0.5 6.188,0.719 0.469,0.219 10 false CANH 5.75,1.042 6.219,1.26 0.469,0.219 10 false CANL 5.74,1.833 6.208,2.052 0.469,0.219 10 false +B1 5.74,2.833 6.208,3.052 0.469,0.219 10 false ACC1 5.719,3.813 6.188,4.031 0.469,0.219 10 false IG 5.729,4.5 6.198,4.719 0.469,0.219 10 false GND1 3.99,1.688 4.969,1.948 0.979,0.26 10 false RADIO NO. 2 4.104,2.688 4.844,2.938 0.74,0.25 10 false ECU-ACC 3.938,3.667 5.021,3.885 1.083,0.219 10 false ECU-IG1 NO. 4 2.198,1.823 3.677,2.115 1.479,0.292 10 false from Battery*2 1.979,2.823 3.313,3.167 1.333,0.344 10 false from ACC Relay*2 1.781,3.781 3.26,4.073 1.479,0.292 10 false from IG1-NO. 1 Relay 0.979,2.25 5.104,2.542 4.125,0.292 10 false from Engine Stop and Start ECU*1 0.979,3.24 5.104,3.531 4.125,0.292 10 false from Engine Stop and Start ECU*1 0.198,5 2.563,5.354 2.365,0.354 10 false *1: w/ Stop and Start System 0.198,5.385 2.563,5.74 2.365,0.354 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H2 radio and display receiver assembly connector.


c.
C369143C68
1.469,0.365 1.885,0.615 0.417,0.25 1.885,2.156 1.885,1.156 1.885,1.156 1.719,1.156 true 2.052,2.156 2.052,1.156 2.052,1.156 2.219,1.156 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.292,1.083 1.781,1.281 0.49,0.198 10 false CANH 2.302,1.083 2.792,1.281 0.49,0.198 10 false CANL 1.573,0.396 2.063,0.594 0.49,0.198 10 false H2
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-13 (CANH) - H2-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Disconnect the H1 radio and display receiver assembly connector.


b.
C414445C04
1.51,0.083 1.917,0.344 0.406,0.26 0.802,1.01 0.792,0.396 0.792,0.396 1.021,0.396 true 0.094,0.063 0.417,0.354 0.323,0.292 10 false *a 1.625,0.115 1.938,0.313 0.313,0.198 10 false H1 1.094,0.313 1.552,0.51 0.458,0.198 10 false GND1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Result
OK
NG



OK

3.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

3.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Measure the voltage according to the value(s) in the table below.

C371295C85
0.375,0.552 0.74,0.76 0.365,0.208 3.667,0.531 4.031,0.74 0.365,0.208 4.604,1.135 4.604,1.552 4.604,1.552 4.438,1.552 true 2.969,0.76 2.969,0.26 2.969,0.26 2.802,0.26 true 2.917,1.01 2.521,1.615 2.521,1.615 2.354,1.615 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 4.198,1.479 4.667,1.667 0.469,0.188 10 false IG 0.469,0.563 0.781,0.76 0.313,0.198 10 false H1 3.76,0.552 4.073,0.75 0.313,0.198 10 false H2 2.5,0.167 2.969,0.354 0.469,0.188 10 false +B1 1.938,1.531 2.406,1.719 0.469,0.188 10 false ACC1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H2-19 (IG) - Body ground Ignition switch ON 11 to 14 V
H1-4 (+B1) - Body ground Always 11 to 14 V
H1-15 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

GO TO STOP AND START SYSTEM (FOR BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Reconnect the cable to the negative (-) battery terminal.


b.

Measure the voltage according to the value(s) in the table below.

C371295C85
0.375,0.552 0.74,0.76 0.365,0.208 3.667,0.531 4.031,0.74 0.365,0.208 4.604,1.135 4.604,1.552 4.604,1.552 4.438,1.552 true 2.969,0.76 2.969,0.26 2.969,0.26 2.802,0.26 true 2.917,1.01 2.521,1.615 2.521,1.615 2.354,1.615 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 4.198,1.479 4.667,1.667 0.469,0.188 10 false IG 0.469,0.563 0.781,0.76 0.313,0.198 10 false H1 3.76,0.552 4.073,0.75 0.313,0.198 10 false H2 2.5,0.167 2.969,0.354 0.469,0.188 10 false +B1 1.938,1.531 2.406,1.719 0.469,0.188 10 false ACC1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H2-19 (IG) - Body ground Ignition switch ON 11 to 14 V
H1-4 (+B1) - Body ground Always 11 to 14 V
H1-15 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)