Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM Y

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the panoramic view monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

HINT:

The panoramic view monitor display may be temporarily distorted due to radio waves around the vehicle.

Problem Symptom Cause
The problem symptom indicates a panoramic view monitor display malfunction and the problem symptom cannot be reproduced. The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.



Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage.*1

Measure the auxiliary battery voltage with the ignition switch off.*2

*1: for Gasoline Model

*2: for HV Model


Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding.


Result:
Proceed to
NEXT



NEXT

4.CHECK NAVIGATION SYSTEM OR AUDIO AND VISUAL SYSTEM
4.CHECK NAVIGATION SYSTEM OR AUDIO AND VISUAL SYSTEM
a.

Refer to the Navigation System or Audio and Visual System.

w/ Navigation System for 8 Inch Display: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>PROBLEM SYMPTOMS TABLE

w/ Navigation System for 12.3 Inch Display: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 12.3 Inch Display)>PROBLEM SYMPTOMS TABLE

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PROBLEM SYMPTOMS TABLE

OK:

Navigation system or Audio and visual system is normal.



Result:
Proceed to
OK
NG



OK

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

NG

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Check for DTCs and note any codes that are output.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353

b.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

c.

Recheck for DTCs. Try to reproduce the DTCs by simulating the original activity that the DTC suggests.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.PROBLEM SYMPTOMS TABLE

B

7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.ADJUST, REPAIR OR REPLACE
8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END