Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086889 METER / GAUGE / DISPLAY _0416706 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150013  Fuel Sender Circuit Open  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area
B150013 Fuel Sender Circuit Open Diagnosis Condition:
·

Ignition switch ON

·

IG power source voltage is 9.5 V or more


Malfunction Status:
·

Voltage signal from fuel sender gauge assembly is 0.2 V or less

·

Voltage signal from fuel sender gauge assembly is 4.7 V or more


Malfunction Time:

10 seconds or more


·

Fuel sender gauge assembly

·

Fuel suction tube with pump and gauge assembly

·

Harness or connector

·

Combination meter assembly



WIRING DIAGRAM

E391293E05
0.125,2.875 3.667,3.271 3.542,0.396 10 false Fuel Suction Tube with Pump and Gauge Assembly 2.229,0.719 2.542,0.917 0.313,0.198 10 false FV 2.229,1.396 2.542,1.594 0.313,0.198 10 false FR 2.24,2.052 2.552,2.25 0.313,0.198 10 false FE 0.438,1.531 1.646,2.125 1.208,0.594 10 false Fuel Sender Gauge Assembly 0.438,1.354 0.594,1.552 0.156,0.198 10 false A 2.615,0.844 3.073,1.042 0.458,0.198 10 false r3 2.583,1.042 2.896,1.24 0.313,0.198 10 false *1 2.604,1.708 2.917,1.906 0.313,0.198 10 false *1 2.604,2.375 2.917,2.573 0.313,0.198 10 false *1 2.99,1.042 3.302,1.24 0.313,0.198 10 false *2 2.99,1.708 3.302,1.906 0.313,0.198 10 false *2 2.99,2.375 3.302,2.573 0.313,0.198 10 false *2 2.948,0.844 3.406,1.042 0.458,0.198 10 false M88 2.625,0.625 2.781,0.823 0.156,0.198 10 false 1 3.01,0.625 3.167,0.823 0.156,0.198 10 false 1 2.635,1.313 2.792,1.51 0.156,0.198 10 false 3 3.031,1.313 3.188,1.51 0.156,0.198 10 false 3 2.646,1.979 2.802,2.177 0.156,0.198 10 false 2 3.031,1.979 3.188,2.177 0.156,0.198 10 false 2 6.375,1.521 6.833,1.719 0.458,0.198 10 false I/F 6.188,0.271 6.646,0.469 0.458,0.198 10 false 5 V 5.875,1.406 6.188,1.604 0.313,0.198 10 false FR 5.875,2.063 6.49,2.26 0.615,0.198 10 false FE 5.865,0.719 6.177,0.917 0.313,0.198 10 false FV 5.281,3.135 7.104,3.542 1.823,0.406 10 false Combination Meter Assembly 5.292,2.979 5.646,3.219 0.354,0.24 10 false H21 1.01,3.385 3.302,3.583 2.292,0.198 10 false *1: for HV Model 2.552,3.385 4.844,3.583 2.292,0.198 10 false *2: for Gasoline Model 5.604,0.719 5.917,0.917 0.313,0.198 10 false 15 5.604,1.406 5.917,1.604 0.313,0.198 10 false 14 5.604,2.073 5.917,2.271 0.313,0.198 10 false 33 1.698,1.188 1.854,1.385 0.156,0.198 10 false 3 2.01,1.417 2.167,1.615 0.156,0.198 10 false 1 1.875,1.875 2.031,2.073 0.156,0.198 10 false 2 2.625,1.521 3.083,1.719 0.458,0.198 10 false r3 2.615,2.188 3.073,2.385 0.458,0.198 10 false r3 2.948,1.521 3.406,1.719 0.458,0.198 10 false M88 2.948,2.188 3.406,2.385 0.458,0.198 10 false M88

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for HV Model A
for Gasoline Model B



A

2.READ VALUE USING GTS

B

6.READ VALUE USING GTS
2.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel level gauge output Min.: 0.00 L, Max.: 655.35 L or Unset
·

Fuel receiver gauge indicates F or 1/1:

56.44 L

·

Fuel receiver gauge indicates 3/4:

48.32 L

·

Fuel receiver gauge indicates 1/2:

32.25 L

·

Fuel receiver gauge indicates 1/4:

16.13 L

·

Fuel receiver gauge indicates E or R:

6.45 L


-
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 409 20

Result:
Result Proceed to
Fuel level data can be displayed on the GTS A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

3.INSPECT FUEL SENDER GAUGE ASSEMBLY
3.INSPECT FUEL SENDER GAUGE ASSEMBLY


Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

4.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
E391971C47
0.458,1.281 0.865,1.521 0.406,0.24 0.323,3.635 0.729,3.875 0.406,0.24 1.719,1.219 1.719,0.677 true 1.396,1.208 1.115,0.802 true 2.042,1.208 2.302,0.813 true 0.594,1.313 1.052,1.51 0.458,0.198 10 false r3 0.479,3.667 0.938,3.865 0.458,0.198 10 false A 0.115,0.083 0.573,0.281 0.458,0.198 10 false *a 1.01,0.625 1.469,0.823 0.458,0.198 10 false FR 1.615,0.49 2.073,0.688 0.458,0.198 10 false FE 2.24,0.646 2.698,0.844 0.458,0.198 10 false FV
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r3-1 (FV) - A-3 Always Below 1 Ω
r3-2 (FE) - A-2 Always Below 1 Ω
r3-3 (FR) - A-1 Always Below 1 Ω
r3-1 (FV) - r3-3 (FR)
or
A-3 - A-1
Always 10 kΩ or higher
r3-1 (FV) - r3-2 (FE)
or
A-3 - A-2
Always 10 kΩ or higher
r3-2 (FE) - r3-3 (FR)
or
A-2 - A-1
Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
r3-1 (FV) - H21-15 (FV) Always Below 1 Ω
r3-3 (FR) - H21-14 (FR) Always Below 1 Ω
r3-2 (FE) - H21-33 (FE) Always Below 1 Ω
r3-1 (FV) or H21-15 (FV) - Body ground Always 10 kΩ or higher
r3-3 (FR) or H21-14 (FR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel level gauge output Min.: 0.00 L, Max.: 655.35 L or Unset
·

Fuel receiver gauge indicates F or 1/1:

60.93 L

·

Fuel receiver gauge indicates 3/4:

50.78 L

·

Fuel receiver gauge indicates 1/2:

33.85 L

·

Fuel receiver gauge indicates 1/4:

16.93 L

·

Fuel receiver gauge indicates E or R:

6.77 L


-
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 409 20

Result:
Result Proceed to
Fuel level data can be displayed on the GTS A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

7.INSPECT FUEL SENDER GAUGE ASSEMBLY
7.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2GR-FKS (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

8.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
E391971C48
0.458,1.281 0.865,1.521 0.406,0.24 0.323,3.635 0.729,3.875 0.406,0.24 1.719,1.219 1.719,0.677 true 1.396,1.208 1.115,0.802 true 2.042,1.208 2.302,0.813 true 0.521,1.313 0.979,1.51 0.458,0.198 10 false M88 0.479,3.667 0.938,3.865 0.458,0.198 10 false A 0.115,0.083 0.573,0.281 0.458,0.198 10 false *a 1.01,0.625 1.469,0.823 0.458,0.198 10 false FR 1.615,0.49 2.073,0.688 0.458,0.198 10 false FE 2.24,0.646 2.698,0.844 0.458,0.198 10 false FV
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M88-1 (FV) - A-3 Always Below 1 Ω
M88-2 (FE) - A-2 Always Below 1 Ω
M88-3 (FR) - A-1 Always Below 1 Ω
M88-1 (FV) - M88-3 (FR)
or
A-3 - A-1
Always 10 kΩ or higher
M88-1 (FV) - M88-2 (FE)
or
A-3 - A-2
Always 10 kΩ or higher
M88-2 (FE) - M88-3 (FR)
or
A-2 - A-1
Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the H21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M88-1 (FV) - H21-15 (FV) Always Below 1 Ω
M88-3 (FR) - H21-14 (FR) Always Below 1 Ω
M88-2 (FE) - H21-33 (FE) Always Below 1 Ω
M88-1 (FV) or H21-15 (FV) - Body ground Always 10 kΩ or higher
M88-3 (FR) or H21-14 (FR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR