Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (FUEL) › FUEL PUMP
RM37A0E _51 Engine / Hybrid System _086907 A25A-FXS, A25B-FXS FUEL _0417787 FUEL PUMP A

A25A-FXS, A25B-FXS FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of fuel pump Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 3.REMOVE BATTERY SERVICE HOLE COVER

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 58912B 7.REMOVE REAR CONSOLE LOWER BOX

Hide 58849 8.REMOVE NO. 2 CONSOLE BOX HOLE COVER (w/o Rear Seat Entertainment System)

Hide 58510D 9.SEPARATE FRONT FLOOR CARPET ASSEMBLY

a.
A455314

Remove the 2 clips.


b.

Disengage the 2 clamps.


c.

Turn back the front floor carpet assembly.


Hide 58556C 10.REMOVE REAR FLOOR SILENCER

Hide 58325E 11.REMOVE REAR FLOOR SERVICE HOLE COVER

a.
A455315

Remove the 3 bolts and rear floor service hole cover from the vehicle body.


Hide 12.DISCONNECT FUEL TANK WIRE

a.
A458402

Disconnect the 2 fuel suction tube with pump and gauge assembly connectors.


b.

Disengage the claw to disconnect the fuel tank wire.


Hide 77018E 13.DISCONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

a.
A458403

Disconnect the fuel tank evaporation vent tube sub-assembly from the fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209F 14.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A458404C01
1.531,2.833 1.417,2.594 1.417,2.594 1.271,2.594 false 2.396,0.344 2.177,0.344 true 2.083,2.802 2.26,2.594 2.26,2.594 2.417,2.594 false 2.417,3.313 2.781,3.313 false 1,3.802 1.135,3.802 1.135,3.802 1.25,3.479 false 2.188,3.604 2.833,3.604 true 2.188,3.448 2.667,3.448 2.667,3.448 2.667,3.594 true 1.865,0.292 1.375,0.292 true 0.781,3.74 1.25,4.052 0.469,0.313 10 false *1 2.875,3.229 3.219,3.448 0.344,0.219 10 false *2 1.135,0.208 1.333,0.396 0.198,0.188 10 true *3 2.51,2.5 2.906,2.906 0.396,0.406 10 false *a 2.906,3.531 3.25,3.948 0.344,0.417 10 false *b 1.063,2.5 1.469,2.844 0.406,0.344 10 false *c 2.469,0.271 2.667,0.458 0.198,0.188 10 true *2
*1 Fuel Suction Plate Sub-assembly
*2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly
*a Fuel Tube Joint
*b O-ring
*c Nylon Tube
V100135

Pull off
V100136

Pull off


Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.




Hide 77144 15.REMOVE FUEL PUMP GAUGE RETAINER

a.
A458405

Disengage the claw to remove the No. 1 fuel tube clamp.


b.

Remove the fuel pump gauge retainer.

i.
A455320C01
0.792,0.708 0.969,0.708 0.969,0.708 1.354,0.927 true 2.385,0.5 2.594,0.25 2.594,0.25 2.781,0.25 true 2.26,1.438 2.469,1.792 2.469,1.792 2.656,1.792 true 0.792,1.344 1.313,1.344 true 0.885,3.01 1.958,3.01 true 2.458,0.833 2.979,0.833 true 2.031,2.927 2.25,3.146 0.219,0.219 10 true *a 2.708,1.698 2.906,1.896 0.198,0.198 10 true *b 0.573,1.25 0.76,1.448 0.188,0.198 10 true *c 0.563,0.615 0.74,0.802 0.177,0.188 10 true *d 2.844,0.156 3.042,0.333 0.198,0.177 10 true *d 3.031,0.74 3.219,0.938 0.188,0.198 10 true *c
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A455321C01
0.542,0.406 0.698,0.406 0.698,0.406 1.115,0.802 true 1.104,2.635 1.708,2.635 true 1.083,1.344 1.24,1.344 1.24,1.344 1.333,1.542 true 2.083,1.271 2.479,1.615 2.479,1.615 2.667,1.615 true 1.729,0.99 2.167,0.813 2.167,0.813 2.313,0.813 true 2.292,1.25 2.646,1.25 true 0.344,0.313 0.51,0.5 0.167,0.188 10 true *a 2.698,1.167 2.875,1.323 0.177,0.156 10 true *b 1.792,2.542 1.99,2.75 0.198,0.208 10 true *c 2.708,1.531 2.885,1.698 0.177,0.167 10 true *d 0.885,1.26 1.052,1.427 0.167,0.167 10 true *d 2.365,0.75 2.542,0.906 0.177,0.156 10 true *e
*a SST (Handle)
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)
*e Extension Bar


Install SST (handle) and an extension bar to SST (plate).

SST
09808-14031  (09808-01010)


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank sub-assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.



Hide 77020A 16.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.
A458406

Remove the fuel suction tube with pump and gauge assembly from the fuel tank sub-assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A455323

Remove the fuel suction tube set gasket from the fuel tank sub-assembly.