This DTC is stored when the blind spot monitor sensor LH (master) judges that there is a communication problem with the blind spot monitor sensor RH (slave).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U0232 | Lost Communication with Blind Spot Monitor Slave Module | The blind spot monitor sensor (master) cannot receive signals from the blind spot monitor sensor (slave) | ·
Open or short in CAN bus main wire or connector ·
Open or short in No. 22 CAN junction connector ·
Blind spot monitor sensor RH (slave) ·
Power source circuit of blind spot monitor sensor RH ·
Blind spot monitor sensor RH ground circuit ·
Blind spot monitor sensor LH (master) ·
Stop and Start System* |
*: w/ Stop and Start System
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ TOYOTA Parking Assist-Sensor System | A |
| w/o TOYOTA Parking Assist-Sensor System | B |
A
B
Using the GTS, check for DTCs according to the prompts on the screen.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>DTC CHECK / CLEAR
The clearance warning ECU assembly does not output DTCs U117787 and U117887 simultaneously.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
| *1 | DLC3 |
| *a | Component with harness connected
(No. 22 CAN Junction Connector) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| M34-1 (CANH) - M34-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or more: Open circuit in main bus lines | |||
| M34-1 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANH short to ground |
| M34-12 (CANL) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANL short to ground |
| M34-1 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| M34-12 (CANL) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| Open circuit in CAN main bus lines | B |
| Short circuit between bus lines | C |
·
Short to ground ·
+B short |
D |
A
B
C
D
Disconnect the M2 blind spot monitor sensor RH (slave) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-10 (BRGD) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M2 blind spot monitor sensor RH (slave) connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M2-5 (BRB) - Body ground | Ignition switch ON | 11 to 14 V*1
10.5 to 16 V*2 |
| M2-5 (BRB) - Body ground | Ignition switch off | Below 1 V |
*1: w/o Stop and Start System
*2: w/ Stop and Start System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Stop and Start System) | B |
| NG (w/ Stop and Start System) | C |
A
B
C
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Reconnect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch off.
Turn the ignition switch to ON.
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs and check if the same DTC is output again.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 22 CAN Junction Connector) |
| *b | to Blind Spot Monitor Sensor LH (Master) CAN Main Wire |
| *c | to Blind Spot Monitor Sensor RH (Slave) CAN Main Wire |
Disconnect the M34 No. 22 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M34-1 (CANH) - M34-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| M34-2 (CANH) - M34-13 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (master) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (slave) CAN main wire) | C |
A
B
C
Reconnect the M34 No. 22 CAN junction connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master)) |
Disconnect the M43 blind spot monitor sensor LH (master) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M43-1 (CA2P) - M43-6 (CA2N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the M34 No. 22 CAN junction connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave)) |
Disconnect the M2 blind spot monitor sensor RH (slave) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-1 (CA2P) -M2-6 (CA2N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 22 CAN Junction Connector) |
| *b | to Blind Spot Monitor Sensor LH (Master) CAN Main Wire |
| *c | to Blind Spot Monitor Sensor RH (Slave) CAN Main Wire |
Disconnect the M34 No. 22 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M34-2 (CANH) - M34-13 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| M34-1 (CANH) - M34-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (master) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (slave) CAN main wire) | C |
A
B
C
Reconnect the M34 No. 22 CAN junction connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master)) |
Disconnect the M43 blind spot monitor sensor LH (master) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M43-1 (CA2P) - M43-6 (CA2N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the M34 No. 22 CAN junction connector.
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave)) |
Disconnect the M2 blind spot monitor sensor RH (slave) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-1 (CA2P) - M2-6 (CA2N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M34 No. 22 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to No. 22 CAN Junction Connector) |
*b | to Blind Spot Monitor Sensor LH (Master) CAN Main Wire |
| *c | to Blind Spot Monitor Sensor RH (Slave) CAN Main Wire | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M34-1 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M34-12 (CANL) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M34-1 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M34-12 (CANL) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M34-2 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M34-13 (CANL) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M34-2 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M34-13 (CANL) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (master) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (slave) CAN main wire) | C |
A
B
C
Reconnect the M34 No. 22 CAN junction connector.
Disconnect the M43 blind spot monitor sensor LH (master) connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (Master)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M43-1 (CA2P) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M43-6 (CA2N) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M43-1 (CA2P) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M43-6 (CA2N) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the M34 No. 22 CAN junction connector.
Disconnect the M2 blind spot monitor sensor RH (slave) connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (Slave)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-1 (CA2P) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M2-6 (CA2N) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| M2-1 (CA2P) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| M2-6 (CA2N) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG