Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SENSOR › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0417855 BLIND SPOT MONITOR SENSOR A

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during blind spot monitor sensor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Rear bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Blind spot monitor sensor Blind spot monitor beam axis adjustment
·

TOYOTA Parking Assist-sensor System (w/o Parking Support Brake System)

·

TOYOTA Parking Assist-sensor System (w/ Parking Support Brake System (Forward/reverse Type))

·

TOYOTA Parking Assist-sensor System (w/ Parking Support Brake System (Reverse Only Type))

·

Parking Support Brake System

·

Blind Spot Monitor System


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link

*: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Rear bumper assembly*
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Blind spot monitor sensor Blind spot monitor beam axis adjustment
·

TOYOTA Parking Assist-sensor System (w/o Parking Support Brake System)

·

TOYOTA Parking Assist-sensor System (w/ Parking Support Brake System (Forward/reverse Type))

·

TOYOTA Parking Assist-sensor System (w/ Parking Support Brake System (Reverse Only Type))

·

Parking Support Brake System

·

Blind Spot Monitor System


(Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1.REMOVE REAR BUMPER ASSEMBLY

Hide 88172 2.REMOVE BLIND SPOT MONITOR SENSOR LH

a.
E432181

Disconnect the connector.


b.

Remove the 3 nuts and blind spot monitor sensor LH.

NOTICE:

Replace the blind spot monitor sensor LH if it has been dropped or subjected to a severe impact.



Hide 88162 3.REMOVE BLIND SPOT MONITOR SENSOR RH

a.
E432182

Disconnect the connector.


b.

Remove the 3 nuts and blind spot monitor sensor RH.

NOTICE:

Replace the blind spot monitor sensor RH if it has been dropped or subjected to a severe impact.