Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING SUPPORT BRAKE SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0420184 PARKING SUPPORT BRAKE SYSTEM C

PARK ASSIST / MONITORING  PARKING SUPPORT BRAKE SYSTEM  U117787  Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message  U117887  Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message  


DESCRIPTION

This DTC is output when the clearance warning ECU assembly detects lost communication with the blind spot monitor sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
U117787 Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor RH (A)
·

Open or short in bus main line

·

Open or short in bus branch line

·

Open or short in wire harness connector (No. 22 CAN junction connector)

·

Clearance warning ECU assembly internal malfunction

·

Blind spot monitor sensor RH (A) nternal malfunction

·

Blind spot monitor sensor RH (A) power source circuit malfunction

·

Blind spot monitor sensor RH (A) internal malfunction

·

Stop and start system*


U117887 Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor LH (B)
·

Open or short in bus main line

·

Open or short in bus branch line

·

Open or short in wire harness connector (No. 22 CAN junction connector)

·

Clearance warning ECU assembly internal malfunction

·

Blind spot monitor sensor LH (B) internal malfunction

·

Blind spot monitor sensor LH (B) power source circuit malfunction

·

Blind spot monitor sensor LH (B) internal malfunction

·

Stop and start system*



*: w/ Stop and Start System


WIRING DIAGRAM

E437401E05
0.135,0.188 1.594,0.615 1.458,0.427 10 false from IG1-NO. 1 Relay*1 1.76,0.354 2.927,0.719 1.167,0.365 10 false ECU-IG1 NO. 3 2.833,1.583 2.99,1.781 0.156,0.198 10 false 1 2.833,1.146 2.99,1.344 0.156,0.198 10 false 5 2.385,3.896 2.979,4.156 0.594,0.26 10 false CANH 2.823,2.302 2.979,2.5 0.156,0.198 10 false 6 1.792,3.146 3.01,3.865 1.219,0.719 10 false Blind Spot Monitor Sensor LH (B) 1.771,3.01 2.229,3.271 0.458,0.26 10 false M43 5.656,3.156 6.854,3.917 1.198,0.76 10 false Blind Spot Monitor Sensor RH (A) 5.646,3.01 5.885,3.271 0.24,0.26 10 false M2 6.813,1.698 6.969,1.896 0.156,0.198 10 false 5 6.792,2.406 7.031,2.667 0.24,0.26 10 false 10 5.542,1.573 5.698,1.771 0.156,0.198 10 false 1 5.531,2.302 5.688,2.5 0.156,0.198 10 false 6 2.479,1.25 3.073,1.51 0.594,0.26 10 false BLB 1.854,2.573 2.448,2.833 0.594,0.26 10 false BLGD 6.323,2.531 6.917,2.792 0.594,0.26 10 false BRGD 5.708,1.583 6.302,1.844 0.594,0.26 10 false CA2P 6.427,1.802 7.021,2.063 0.594,0.26 10 false BRB 2.396,2.323 2.99,2.583 0.594,0.26 10 false CA2N 5.708,2.313 6.302,2.573 0.594,0.26 10 false CA2N 1.552,4.708 2.021,5.01 0.469,0.302 10 false H46 1.896,4.708 3.115,5.354 1.219,0.646 10 false Clearance Warning ECU Assembly 3.781,4.76 5.094,5.427 1.313,0.667 10 false No. 22 CAN Junction Connector 2.385,4.375 2.979,4.635 0.594,0.26 10 false CANL 2.854,4.26 3.385,4.552 0.531,0.292 10 false 38 2.844,3.781 3.229,4.094 0.385,0.313 10 false 37 3.563,4.344 3.917,4.563 0.354,0.219 10 false M34 3.552,2.385 3.906,2.604 0.354,0.219 10 false M34 3.542,1.667 3.896,1.885 0.354,0.219 10 false M34 4.573,1.688 4.927,1.906 0.354,0.219 10 false M34 4.573,2.385 4.927,2.604 0.354,0.219 10 false M34 3.635,1.469 3.792,1.667 0.156,0.198 10 false 2 4.615,2.177 4.885,2.375 0.271,0.198 10 false 12 4.646,1.469 4.802,1.667 0.156,0.198 10 false 1 3.552,3.875 3.906,4.094 0.354,0.219 10 false M34 3.635,3.677 3.792,3.875 0.156,0.198 10 false 3 3.594,4.146 3.865,4.344 0.271,0.198 10 false 14 2.417,1.604 3.01,1.865 0.594,0.26 10 false CA2P 3.583,2.177 3.854,2.375 0.271,0.198 10 false 13 1.594,2.448 1.813,2.656 0.219,0.208 10 false 10 0.115,0.646 2.25,0.865 2.135,0.219 10 false from Engine Stop and Start ECU*2 0.26,5.302 2.396,5.521 2.135,0.219 10 false *1: w/o Stop and Start System 2.458,5.302 4.594,5.521 2.135,0.219 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for parking support brake system DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 only is output A
DTC U117887 only is output B
DTC U117787 and U117887 are output C



A

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)

B

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BODY GROUND)

C

6.CHECK CAN BUS MAIN WIRE
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - BODY GROUND)
a.
E435677C03
1.5,0.333 2,0.583 0.5,0.25 2.573,1.865 2.01,1.385 true 1.656,0.375 2.01,0.583 0.354,0.208 10 false M2 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.667,1.781 3.167,1.979 0.5,0.198 10 false BRGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Disconnect the connector of the blind spot monitor sensor RH (A).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-10 (BRGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - POWER SOURCE)
a.
E435677C49
1.5,0.302 1.958,0.552 0.458,0.25 2.552,0.635 2.302,0.635 2.302,0.635 2.01,1.167 true 1.615,0.344 1.969,0.552 0.354,0.208 10 false M2 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.635,0.552 3.135,0.75 0.5,0.198 10 false BRB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Disconnect the blind spot monitor sensor RH (A) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M2-5 (BRB) - Body ground Ignition switch ON 11 to 14 V*1
10.5 to 16 V*2
M2-5 (BRB) - Body ground Ignition switch off Below 1 V


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - BODY GROUND)
a.
E435677C01
1.5,0.25 2,0.5 0.5,0.25 2.021,1.375 2.594,1.854 true 1.625,0.302 1.979,0.51 0.354,0.208 10 false M43 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.656,1.792 3.156,1.99 0.5,0.198 10 false BLGD
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Disconnect the connector of the blind spot monitor sensor LH (B) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-10 (BLGD) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - POWER SOURCE)
a.
E435677C02
1.5,0.25 2,0.5 0.5,0.25 2.042,1.146 2.563,0.615 true 1.625,0.292 1.979,0.5 0.354,0.208 10 false M43 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 2.646,0.552 3.146,0.75 0.5,0.198 10 false BLB
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Disconnect the connector of the blind spot monitor sensor LH (B).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M43-5 (BLB) - Body ground Ignition Switch ON 11 to 14 V*1
10.5 to 16 V*2
M43-5 (BLB) - Body ground Ignition switch off Below 1 V


*1: w/o Stop and Start System

*2: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

6.CHECK CAN BUS MAIN WIRE
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.


c.
E395856C20
1.49,2.792 1.938,3.031 0.448,0.24 0.24,1.448 0.635,1.708 0.396,0.26 1.073,2.948 1.26,2.948 1.26,2.948 1.604,3.417 true 2.333,3.917 2.49,4.302 2.49,4.302 2.635,4.302 true 2.115,1.875 2.646,2.604 2.646,2.604 2.792,2.604 true 2.063,1.583 2.75,0.75 2.75,0.75 2.896,0.75 true 0.24,2.708 0.552,2.865 0.313,0.156 10 false *b 0.167,0.115 0.479,0.271 0.313,0.156 10 false *a 1.573,2.833 1.927,3.031 0.354,0.198 10 false H56 0.292,1.49 0.698,1.688 0.406,0.198 10 false M34 2.938,0.688 3.427,0.885 0.49,0.198 10 false CANH 2.865,2.521 3.292,2.729 0.427,0.208 10 false CANL 2.698,4.208 3.281,4.417 0.583,0.208 10 false BAT 0.813,2.854 1.125,3.063 0.313,0.208 10 false CG
*a Component with wire harness connected
(No. 22 CAN Junction Connector)
*b DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Problem Symptom if Specified Condition Not Met
M34-3 (CANH) - M34-14 (CANL) Disconnect cable from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or more: Open circuit in main bus lines
M34-3 (CANH) - H56-4 (CG) Disconnect cable from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH short to ground
M34-14 (CANL) - H56-4 (CG) Disconnect cable from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL short to ground
M34-3 (CANH) - H56-16 (BAT) Disconnect cable from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
M34-14 (CANL) - H56-16 (BAT) Disconnect cable from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
Open circuit in CAN main bus lines B
Short circuit between bus lines C
·

Short to ground

·

+B short


D



A

7.CLEAR DTCS

B

9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 22 JUNCTION CONNECTOR)

C

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 22 JUNCTION CONNECTOR)

D

17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 22 CAN JUNCTION CONNECTOR)
7.CLEAR DTCS
a.

Using the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs
50002 438

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes
50001 438

Result:
Result Proceed to
DTC U117787 and U117887 are not output A
DTC U117787 and U117887 are output B



A

B

9.CHECK FOR OPEN IN CAN BUS WIRE (NO. 22 JUNCTION CONNECTOR)
a.

Disconnect the M34 No. 22 CAN junction connector.

E429360C02
3.177,0.396 3.583,0.646 0.406,0.25 2.896,1.438 2.688,0.469 true 2.896,1.771 2.76,2.24 true 2.698,1.781 2.125,2.26 true 2.531,1.771 1.521,2.042 true 1.51,1.302 2.521,1.49 true 2.719,1.438 2.344,0.635 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.958,1.219 1.625,1.458 0.667,0.24 10 false CANH*c 2.396,2.271 3.063,2.51 0.667,0.24 10 false CANL*b 2.417,0.24 3.083,0.479 0.667,0.24 10 false CANH*b 1.844,2.271 2.51,2.51 0.667,0.24 10 false CANL*d 1,1.99 1.667,2.229 0.667,0.24 10 false CANL*c 2.052,0.469 2.719,0.708 0.667,0.24 10 false CANH*d 3.24,0.438 3.74,0.677 0.5,0.24 10 false M34
*a Front view of wire harness connector
(to No. 22 CAN Junction Connector)
*b to Clearance Warning ECU Assembly CAN Wire
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire *d to Blind Spot Monitor Sensor LH (B) CAN Main Wire



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-3 (CANH) - M34-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M34-2 (CANH) - M34-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
M34-1 (CANH) - M34-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 22 CAN JUNCTION CONNECTOR

B

10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))

C

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))

D

12.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
10.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR LH (B))
a.
E435677C05
1.51,0.302 1.969,0.552 0.458,0.25 0.823,1.833 1.323,1.365 true 0.792,0.74 1.333,1.167 true 1.615,0.344 1.969,0.552 0.354,0.208 10 false M43 0.375,0.594 0.875,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.427,1.781 0.927,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the M43 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-1 (CA2P) - M43-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 22 CAN JUNCTION CONNECTOR)

11.CHECK FOR OPEN IN CAN BUS MAIN WIRE (BLIND SPOT MONITOR SENSOR RH (A))
a.
E435677C06
1.51,0.302 1.969,0.552 0.458,0.25 1.365,1.125 0.802,0.698 true 1.344,1.375 0.875,1.833 true 1.615,0.344 1.969,0.552 0.354,0.208 10 false M2 0.396,0.594 0.896,0.792 0.5,0.198 10 false CA2P 0.135,0.094 0.635,0.292 0.5,0.198 10 false *a 0.458,1.781 0.958,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the M2 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-1 (CA2P) - M2-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 22 CAN JUNCTION CONNECTOR)

12.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY)
a.
C369149C81
1.5,0.5 1.917,0.75 0.417,0.25 2.271,2.385 2.708,1.823 true 2.375,2.615 2.844,1.833 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.833,2.344 2.24,2.531 0.406,0.188 10 false CANH 1.594,0.542 1.906,0.74 0.313,0.198 10 false H46 2.031,2.635 2.438,2.823 0.406,0.188 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the H46 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-37 (CANH) - H46-38 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 22 CAN JUNCTION CONNECTOR)

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 22 JUNCTION CONNECTOR)
a.

Disconnect the No. 22 CAN junction connector.

E429360C02
3.177,0.396 3.583,0.646 0.406,0.25 2.896,1.438 2.688,0.469 true 2.896,1.771 2.76,2.24 true 2.698,1.781 2.125,2.26 true 2.531,1.771 1.521,2.042 true 1.51,1.302 2.521,1.49 true 2.719,1.438 2.344,0.635 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 0.958,1.219 1.625,1.458 0.667,0.24 10 false CANH*c 2.396,2.271 3.063,2.51 0.667,0.24 10 false CANL*b 2.417,0.24 3.083,0.479 0.667,0.24 10 false CANH*b 1.844,2.271 2.51,2.51 0.667,0.24 10 false CANL*d 1,1.99 1.667,2.229 0.667,0.24 10 false CANL*c 2.052,0.469 2.719,0.708 0.667,0.24 10 false CANH*d 3.24,0.438 3.74,0.677 0.5,0.24 10 false M34
*a Front view of wire harness connector
(to No. 22 CAN Junction Connector)
*b to Clearance Warning ECU Assembly CAN Wire
*c to Blind Spot Monitor Sensor RH (A) CAN Main Wire *d to Blind Spot Monitor Sensor LH (B) CAN Main Wire



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-3 (CANH) - M34-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
M34-2 (CANH) - M34-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
M34-1 (CANH) - M34-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 22 CAN JUNCTION CONNECTOR

B

14.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

C

15.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

D

16.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
14.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.
E435677C07
1.51,0.302 1.969,0.552 0.458,0.25 0.927,1.792 1.344,1.375 true 0.802,0.698 1.333,1.167 true 1.604,0.354 1.958,0.563 0.354,0.208 10 false M43 0.375,0.594 0.875,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.427,1.781 0.927,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))


Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the M43 blind spot monitor sensor LH (B) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-1 (CA2P) - M43-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 22 CAN JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.
E435677C08
1.51,0.302 1.969,0.552 0.458,0.25 1.323,1.125 0.813,0.74 true 1.323,1.365 0.854,1.781 true 1.646,0.344 2,0.552 0.354,0.208 10 false M2 0.396,0.594 0.896,0.792 0.5,0.198 10 false CA2P 0.156,0.083 0.656,0.281 0.5,0.198 10 false *a 0.458,1.781 0.958,1.979 0.5,0.198 10 false CA2N
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))


Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the M2 blind spot monitor sensor RH (A) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-1 (CA2P) - M2-6 (CA2N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 22 CAN JUNCTION CONNECTOR)

16.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
C369149C82
1.5,0.5 1.917,0.75 0.417,0.25 2.26,2.427 2.729,1.833 true 2.438,2.688 2.833,1.844 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.833,2.344 2.24,2.531 0.406,0.188 10 false CANH 1.604,0.552 1.917,0.75 0.313,0.198 10 false H46 2.031,2.635 2.438,2.823 0.406,0.188 10 false CANL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the H46 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-37 (CANH) - H46-38 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 22 CAN JUNCTION CONNECTOR)

17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 22 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 22 CAN junction connector.

E407528C05
0.427,1.333 0.875,1.583 0.448,0.25 4.052,1.25 4.5,1.5 0.448,0.25 1.125,0.573 1.292,0.573 1.292,0.573 1.479,1.365 true 1.063,2.25 1.229,2.25 1.229,2.25 1.479,1.708 true 1.542,0.188 1.708,0.188 1.708,0.188 1.667,1.354 true 1.833,2.563 2,2.563 2,2.563 1.656,1.719 true 2.417,0.469 2.25,0.469 2.25,0.469 1.854,1.344 true 2.375,2.406 2.208,2.406 2.208,2.406 1.844,1.729 true 5.635,2.302 5.802,2.302 5.802,2.302 6.146,1.625 true 6,0.573 5.833,0.573 5.833,0.573 5.552,1.177 true 0.302,0.479 0.615,0.677 0.313,0.198 10 false *a 4.323,0.563 4.635,0.76 0.313,0.198 10 false *b 0.563,0.469 1.177,0.677 0.615,0.208 10 false CANH*d 0.531,2.167 1.146,2.375 0.615,0.208 10 false CANL*d 0.979,0.104 1.594,0.313 0.615,0.208 10 false CANH*e 1.292,2.469 1.906,2.677 0.615,0.208 10 false CANL*e 2.469,0.396 3.083,0.604 0.615,0.208 10 false CANH*c 2.417,2.333 3.031,2.542 0.615,0.208 10 false CANL*c 0.51,1.375 0.958,1.635 0.448,0.26 10 false M34 4.115,1.302 4.563,1.563 0.448,0.26 10 false H56 5.323,2.24 5.938,2.448 0.615,0.208 10 false BAT 6.063,0.49 6.677,0.698 0.615,0.208 10 false CG
*a Front view of wire harness connector
(to No. 22 CAN Junction Connector)
*b Front view of DLC3
*c to Clearance Warning ECU Assembly CAN Wire *d to Blind Spot Monitor Sensor RH (A) CAN Main Wire
*e to Blind Spot Monitor Sensor LH (B) CAN Main Wire - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M34-1 (CANH) - H56-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M34-12 (CANL) - H56-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M34-1 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M34-12 (CANL) - H56-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M34-2 (CANH) - H56-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M34-13 (CANL) - H56-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M34-2 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M34-13 (CANL) - H56-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M34-3 (CANH) - H56-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M34-14 (CANL) - H56-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
M34-3 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M34-14 (CANL) - H56-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


HINT:

Check for short that was confirmed to be a malfunction by confirming symptoms.



Result:
Result Proceed to
OK A
NG (to blind spot monitor sensor LH (B) CAN main wire) B
NG (to blind spot monitor sensor RH (A) CAN main wire) C
NG (to clearance warning ECU assembly CAN wire) D



A

REPLACE NO. 22 CAN JUNCTION CONNECTOR

B

18.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))

C

19.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))

D

20.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
18.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR LH (B))
a.
E401716C20
1.458,2.823 1.865,3.073 0.406,0.25 1.406,0.406 1.813,0.656 0.406,0.25 1.229,1.5 0.698,2.135 true 1.24,1.354 0.74,0.917 true 0.729,2.781 0.927,2.781 0.927,2.781 1.604,3.396 true 2.354,3.948 2.552,3.948 2.552,3.948 3.021,3.5 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.208,2.729 0.521,2.927 0.313,0.198 10 false *1 0.25,2.094 0.865,2.292 0.615,0.198 10 false CA2N 0.26,0.833 0.875,1.031 0.615,0.198 10 false CA2P 2.885,3.333 3.427,3.542 0.542,0.208 10 false BAT 1.552,2.854 2.01,3.052 0.458,0.198 10 false H56 1.49,0.438 1.948,0.635 0.458,0.198 10 false M43 0.51,2.708 1.052,2.917 0.542,0.208 10 false CG
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH (B))
*1 DLC3


Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the connector of the blind spot monitor sensor LH (B).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M43-1 (CA2P) - H56-4 (CG) Disconnect cable from negative (-) auxiliary battery terminal 200 Ω or higher
M43-6 (CA2N) - H56-4 (CG) Disconnect cable from negative (-) auxiliary battery terminal 200 Ω or higher
M43-1 (CA2P) - H56-16 (BAT) Disconnect cable from negative (-) auxiliary battery terminal 6 kΩ or higher
M43-6 (CA2N) - H56-16 (BAT) Disconnect cable from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR LH (B) - NO. 22 CAN JUNCTION CONNECTOR)

19.CHECK FOR SHORT IN CAN BUS WIRES (BLIND SPOT MONITOR SENSOR RH (A))
a.
E401716C21
1.458,2.823 1.865,3.073 0.406,0.25 1.406,0.406 1.813,0.656 0.406,0.25 2.354,3.792 2.844,3.521 true 1.229,1.5 0.698,2.135 true 1.24,1.354 0.74,0.917 true 0.719,2.927 0.927,2.927 0.927,2.927 1.594,3.385 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.208,2.729 0.521,2.927 0.313,0.198 10 false *1 0.25,2.094 0.865,2.292 0.615,0.198 10 false CA2N 0.26,0.833 0.875,1.031 0.615,0.198 10 false CA2P 2.885,3.333 3.427,3.542 0.542,0.208 10 false BAT 1.552,2.854 2.01,3.052 0.458,0.198 10 false H56 1.49,0.438 1.948,0.635 0.458,0.198 10 false M2 0.49,2.844 1.031,3.052 0.542,0.208 10 false CG
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH (A))
*1 DLC3


Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the M2 blind spot monitor sensor RH (A).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-1 (CA2P) - H56-4 (CG) Disconnect cable from negative (-) auxiliary battery terminal 200 Ω or higher
M2-6 (CA2N) - H56-4 (CG) Disconnect cable from negative (-) auxiliary battery terminal 200 Ω or higher
M2-1 (CA2P) - H56-16 (BAT) Disconnect cable from negative (-) auxiliary battery terminal 6 kΩ or higher
M2-6 (CA2N) - H56-16 (BAT) Disconnect cable from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH (A) - NO. 22 CAN JUNCTION CONNECTOR)

20.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
E401717C10
1.458,2.823 1.865,3.073 0.406,0.25 1.479,0.521 1.885,0.771 0.406,0.25 2.354,3.792 2.844,3.521 true 2.625,1.427 3.115,2.51 true 2.521,1.406 2.375,2.26 true 0.625,2.979 0.844,2.969 0.844,2.969 1.604,3.406 true 0.167,0.177 0.479,0.375 0.313,0.198 10 false *a 0.208,2.729 0.521,2.927 0.313,0.198 10 false *1 2.188,2.323 2.802,2.521 0.615,0.198 10 false CANH 2.979,2.552 3.427,2.75 0.448,0.198 10 false CANL 2.885,3.333 3.427,3.542 0.542,0.208 10 false BAT 1.552,2.854 2.01,3.052 0.458,0.198 10 false H56 1.552,0.542 2.01,0.74 0.458,0.198 10 false H46 0.385,2.917 0.927,3.125 0.542,0.208 10 false CG
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*1 DLC3


Reconnect the M34 No. 22 CAN junction connector.


b.

Disconnect the connector of the clearance warning ECU assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-37 (CANH) - H56-4 (CG) Disconnect cable from negative (-) auxiliary battery terminal 200 Ω or higher
H46-38 (CANL) - H56-4 (CG) Disconnect cable from negative (-) auxiliary battery terminal 200 Ω or higher
H46-37 (CANH) - H56-16 (BAT) Disconnect cable from negative (-) auxiliary battery terminal 6 kΩ or higher
H46-38 (CANL) - H56-16 (BAT) Disconnect cable from negative (-) auxiliary battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY - NO. 22 CAN JUNCTION CONNECTOR)