Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM(for 8 Inch Display) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 8 Inch Display)  B1543  Extension Module Disconnected 2  


DESCRIPTION

If the radio and display receiver assembly cannot detect the navigation ECU for a certain period of time (90 seconds) after the ignition switch is turned to ACC and the radio and display receiver assembly confirms that the information is missing by checking past navigation ECU recognition information (registered information), this DTC will be stored.

HINT:

The navigation system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the navigation system will not operate normally.


DTC No. Detection Item DTC Detection Condition Trouble Area
B1543 Extension Module Disconnected 2 Navigation ECU disconnected
·

Navigation ECU

·

Radio and display receiver assembly

·

Harness or connector

·

Stop and start system*



*: w/ Stop and Start System


HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.


WIRING DIAGRAM

E410029E02
5.708,2.375 6.906,2.99 1.198,0.615 10 false Radio and Display Receiver Assembly 5.708,2.198 6.156,2.51 0.448,0.313 10 false d3 3.292,2.229 4.448,2.76 1.156,0.531 10 false Navigation ECU 2.979,1.781 3.594,2.167 0.615,0.385 10 false H18 4.333,1.781 4.75,2.156 0.417,0.375 10 false d1 2.969,0.823 3.448,1.229 0.479,0.406 10 false H18 4.333,1.313 4.75,1.688 0.417,0.375 10 false d1 4.333,0.823 4.75,1.198 0.417,0.375 10 false d1 1.938,0.99 3.094,1.521 1.156,0.531 10 false RADIO 0.01,0.833 1.542,1.219 1.531,0.385 10 false from Auxiliary Battery*2 3.375,0.823 3.865,1.219 0.49,0.396 10 false +B 3.365,1.781 3.854,2.177 0.49,0.396 10 false GND 3.813,0.823 4.302,1.219 0.49,0.396 10 false US4+ 3.833,1.302 4.323,1.698 0.49,0.396 10 false US4- 3.771,1.781 4.26,2.177 0.49,0.396 10 false UGD4 5.885,0.885 6.375,1.281 0.49,0.396 10 false US4+ 5.896,1.323 6.385,1.719 0.49,0.396 10 false US4- 5.896,1.781 6.385,2.177 0.49,0.396 10 false UGD4 4.385,0.625 4.802,1 0.417,0.375 10 false 4 4.385,1.115 4.802,1.49 0.417,0.375 10 false 5 4.385,1.583 4.802,1.958 0.417,0.375 10 false 6 3.01,0.646 3.427,1.021 0.417,0.375 10 false 10 3,1.594 3.417,1.969 0.417,0.375 10 false 23 5.698,0.708 6.115,1.083 0.417,0.375 10 false 1 5.708,1.198 6.125,1.542 0.417,0.344 10 false 2 5.708,1.677 6.125,2.021 0.417,0.344 10 false 3 1.156,3.344 2.906,3.635 1.75,0.292 10 false : USB Communication Line 0.552,2.333 1.875,2.667 1.323,0.333 10 false *1: Shielded 5.167,1.552 5.479,1.781 0.313,0.229 10 false *1 0.417,1.313 2.094,1.854 1.677,0.542 10 false from Engine Stop and Start ECU*3 0.552,2.667 2.563,3.021 2.01,0.354 10 false *2: w/o Stop and Start System 0.552,3.021 3.01,3.385 2.458,0.365 10 false *3: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK MAP SCREEN
a.

Turn the ignition switch to ACC and wait for 90 seconds.


b.

Press the "MAP" switch and check that the map screen is displayed normally.


Result:
Result Proceed to
Map screen is displayed normally A
Map screen is not displayed normally B


HINT:
·

This DTC may be stored due to environmental reasons such as electrical noise or interference.

·

Clear past DTCs when the map screen is displayed normally. (Codes stored due to past environmental factors)




A

B

2.CHECK DTC
2.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON and wait for 90 seconds.


d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - AUXILIARY BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - AUXILIARY BATTERY AND BODY GROUND)
a.
E364286C71
1.5,0.333 1.917,0.583 0.417,0.25 2.573,1.302 2.813,0.823 2.813,0.823 2.99,0.823 true 2.448,1.51 2.708,2.01 2.708,2.01 2.875,2.01 true 0.198,0.146 0.51,0.344 0.313,0.198 10 false *a 1.583,0.375 2.042,0.573 0.458,0.198 10 false H18 2.938,1.948 3.271,2.125 0.333,0.177 10 false GND 3.063,0.76 3.302,0.938 0.24,0.177 10 false +B
*a Front view of wire harness connector
(to Navigation ECU)


Disconnect the H18 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-23 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H18-10 (+B) - Body ground*1 Ignition switch off 11 to 14 V
H18-10 (+B) - Body ground*2 Always 11 to 14 V*3
10.5 to 16 V*4


*1: for HV Model

*2: for Gasoline Model

*3: w/o Stop and Start System

*4: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.
E368007C55
1.49,0.5 1.906,0.75 0.417,0.25 1.479,2.667 1.896,2.917 0.417,0.25 1.156,2.031 1.354,2.031 1.354,2.031 1.708,1.469 true 1.813,1.333 2.219,0.979 2.219,0.979 2.427,0.979 true 1.031,0.906 1.219,0.906 1.219,0.906 1.615,1.354 true 2,3.427 2.396,4.135 2.396,4.135 2.615,4.135 true 1.042,2.979 1.229,2.979 1.229,2.979 1.875,3.438 true 1.406,4.146 1.604,4.146 1.604,4.146 1.958,3.583 true 0.271,0.146 0.583,0.302 0.313,0.156 10 false *a 0.323,2.448 0.635,2.604 0.313,0.156 10 false *b 1.625,0.542 2.052,0.76 0.427,0.219 10 false d3 1.615,2.708 2.177,2.979 0.563,0.271 10 false d1 2.479,0.896 3.052,1.125 0.573,0.229 10 false US4- 0.635,0.813 1.208,1.042 0.573,0.229 10 false US4+ 0.729,1.948 1.302,2.177 0.573,0.229 10 false UGD4 0.99,4.073 1.563,4.302 0.573,0.229 10 false UGD4 0.646,2.885 1.219,3.115 0.573,0.229 10 false US4+ 2.667,4.063 3.24,4.292 0.573,0.229 10 false US4-
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Navigation ECU)


Disconnect the d1 navigation ECU connector.


b.

Disconnect the d3 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-4 (US4+) - d3-1 (US4+) Always Below 1 Ω
d1-5 (US4-) - d3-2 (US4-) Always Below 1 Ω
d1-6 (UGD4) - d3-3 (UGD4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE NAVIGATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON and wait for 90 seconds.


d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NAVIGATION ECU IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY