Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM(for 8 Inch Display) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 8 Inch Display)  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication line.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing
·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector

·

Stop and start system*



*: w/ Stop and Start System


HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E432624E02
0.177,0.594 1.875,0.885 1.698,0.292 10 false from Auxiliary Battery*1 0.49,1.938 1.635,2.135 1.146,0.198 10 false from ACC Relay*1 1.115,5.333 3.406,5.542 2.292,0.208 10 false : AVC-LAN Communication Line 1.948,3.958 2.865,4.156 0.917,0.198 10 false H1 1.948,4.104 4.573,4.375 2.625,0.271 10 false Radio and Display Receiver Assembly 3.219,3.281 3.688,3.5 0.469,0.219 10 false TX1+ 3.25,3.677 3.615,3.896 0.365,0.219 10 false TX1- 0.323,1.073 3.198,1.292 2.875,0.219 10 false from Eco Run Vehicle Converter Assembly*2 2.76,0.75 3.552,0.938 0.792,0.188 10 false AMP NO. 1 2.781,2.073 3.438,2.281 0.656,0.208 10 false ECU-ACC 5.594,0.594 6.51,0.792 0.917,0.198 10 false +B 5.594,1.938 6.51,2.135 0.917,0.198 10 false ACC 5.594,3.281 6.51,3.479 0.917,0.198 10 false TX+ 5.604,3.688 6.521,3.885 0.917,0.198 10 false TX- 5.573,4.229 6.49,4.427 0.917,0.198 10 false GND 4.688,5.063 7.156,5.313 2.469,0.25 10 false Stereo Component Amplifier Assembly 5.281,4.01 6.198,4.208 0.917,0.198 10 false 3 5.26,1.729 6.177,1.948 0.917,0.219 10 false 12 5.208,0.604 6.125,0.823 0.917,0.219 10 false M37 5.292,0.406 6.208,0.625 0.917,0.219 10 false 1 0.365,4.583 2.906,4.781 2.542,0.198 10 false *1: w/o Stop and Start System 0.396,4.917 2.938,5.115 2.542,0.198 10 false *2: w/ Stop and Start System 3.625,3.125 3.938,3.375 0.313,0.25 10 false 5 3.625,3.521 4.031,3.729 0.406,0.208 10 false 6 5.292,3.073 5.698,3.281 0.406,0.208 10 false 8 5.302,3.49 5.615,3.74 0.313,0.25 10 false 7 5.219,4.219 6.135,4.438 0.917,0.219 10 false M37 5.208,1.927 6.125,2.146 0.917,0.219 10 false M38 5.208,3.292 6.125,3.51 0.917,0.219 10 false M38 5.198,3.688 6.115,3.906 0.917,0.219 10 false M38 0.323,2.406 3.198,2.625 2.875,0.219 10 false from Eco Run Vehicle Converter Assembly*2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>PRECAUTION



PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.


Result:
Result Proceed to
DTC B15C3 is not output A
DTC B15C3 is output B



A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.




Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B



A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

4.CHECK DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the M37 and M38 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M37-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M37-1 (+B) - M37-3 (GND)*1 Ignition switch off 11 to 14 V
M37-1 (+B) - M37-3 (GND)*2 Always 11 to 14 V*3
9.5 to 14 V*4
M38-12 (ACC) - M37-3 (GND) Ignition switch ACC 11 to 14 V*3
9.5 to 14 V*4


*1: for HV Model

*2: for Gasoline Model

*3: w/o Stop and Start System

*4: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H1 radio and display receiver assembly connector.


b.

Disconnect the M38 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H1-5 (TX1+) - M38-8 (TX+) Always Below 1 Ω
H1-6 (TX1-) - M38-7 (TX-) Always Below 1 Ω
H1-5 (TX1+) or M38-8 (TX+) - Body ground Always 10 kΩ or higher
H1-6 (TX1-) or M38-7 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY