Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086895 SEAT BELT _0420373 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter assembly illuminates, blinks or turns off the seat belt warning light on the combination meter assembly in accordance with the state of the front seat inner belt assembly (driver seat).

WIRING DIAGRAM

B287218E92
4.167,0.813 4.438,1.052 0.271,0.24 10 false 4D 4.188,0.625 4.385,0.792 0.198,0.167 10 false 33 2.677,0.844 3.073,1.229 0.396,0.385 10 false DBKL 0.094,1.531 1.292,2.031 1.198,0.5 10 false Combination Meter Assembly 0.573,2.448 2.292,2.656 1.719,0.208 10 false : CAN Communication Line 3.125,0.708 3.323,0.938 0.198,0.229 10 false 18 5.26,0.719 5.458,0.99 0.198,0.271 10 false 3 6.094,0.719 6.333,1.063 0.24,0.344 10 false 2 1.708,1.688 3.354,2.063 1.646,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 4.844,1.094 5.99,1.271 1.146,0.177 10 false M71*1, M28*2 4.833,1.271 6.771,1.75 1.938,0.479 10 false Front Seat Inner Belt Assembly (Driver Seat) 3.5,1.25 4.583,1.792 1.083,0.542 10 false Instrument Panel Junction Block Assembly 1.708,1.531 1.979,1.771 0.271,0.24 10 false MB 5.427,0.729 5.583,0.927 0.156,0.198 10 false + 5.875,0.74 6.031,0.938 0.156,0.198 10 false E 2.875,2.469 4.021,2.646 1.146,0.177 10 false *1: for LHD 4.052,2.479 5.198,2.656 1.146,0.177 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

The vehicle auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




HINT:
·

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION

·

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL



PROCEDURE

1.READ VALUE USING GTS (D SEAT BUCKLE SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch OFF or ON OFF: Driver seat belt fastened
ON: Driver seat belt unfastened
-
Body Electrical > Main Body > Data List
Tester Display
D Seat Buckle SW
50003 123 14
OK:

ON or OFF appears on the GTS screen according to the driver seat belt condition.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)
2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT)

OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B491251C12
1.948,0.719 2.365,0.958 0.417,0.24 5.552,0.625 5.948,0.865 0.396,0.24 2.417,2 2.417,1.573 false 5.667,0.656 5.979,0.854 0.313,0.198 10 false 4D 2.052,0.76 2.365,0.958 0.313,0.198 10 false MB 0.344,0.167 0.656,0.365 0.313,0.198 10 false *a 2.25,2 2.865,2.198 0.615,0.198 10 false DBKL
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the 4D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-18 (DBKL) - 4D-33 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SEAT) - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
M71-3 (+) - 4D-33 Always Below 1 Ω
M71-3 (+) or 4D-33 - Body ground Always 10 kΩ or higher
M71-2 (E) - Body ground Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
M28-3 (+) - 4D-33 Always Below 1 Ω
M28-3 (+) or 4D-33 - Body ground Always 10 kΩ or higher
M28-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR