Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2020.11
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418593 POWER BACK DOOR SYSTEM Y

DOOR / HATCH  POWER BACK DOOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

The power back door system troubleshooting procedure is based on the premise that the entry and start system (for Entry Function) is operating normally. Check the entry and start system (for Entry Function) first before troubleshooting the power back door system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Use the following procedure to troubleshoot the power back door system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points for problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms



Result:
Proceed to
NEXT



NEXT

3.PRE-CHECK
3.PRE-CHECK
a.

Measure the auxiliary battery voltage with the ignition switch off.*1


b.

Measure the auxiliary battery voltage.*2

*1: for HV Model

*2: for Gasoline Model


Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.


c.

Check the fuses and relays.


d.

Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


Result:
Proceed to
NEXT



NEXT

4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output B



A

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

B

5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
a.

Using the GTS, check for LIN communication system DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
LIN DTCs are not output A
LIN DTCs are output B



A

6.CHECK FOR DTC (MULTIPLEX NETWORK DOOR ECU)*

B

6.CHECK FOR DTC (MULTIPLEX NETWORK DOOR ECU)*
a.

Clear the DTCs.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Back Door > Clear DTCs
50002 159

b.

Recheck for DTCs.

Body Electrical > Back Door > Trouble Codes
50001 159

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

7.PROBLEM SYMPTOMS TABLE

B

7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.ADJUST, REPAIR OR REPLACE
8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
a.

Check if the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors have been disconnected, the cable has been disconnected from the negative (-) auxiliary battery terminal with the back door open or if any of the fuses in the power source circuit have been removed and installed or replaced.


Result:
Result Proceed to
The multiplex network door ECU has been removed and installed or replaced, any of the connectors have been disconnected, the cable has been disconnected from the negative (-) auxiliary battery terminal with the back door open, or any of the fuses in the power source circuit have been removed and installed or replaced. A
The multiplex network door ECU has not been removed and installed or replaced and none of the connectors have been disconnected, the cable has not been disconnected from the negative (-) auxiliary battery terminal with the back door open and none of the fuses in the power source circuit have been removed and installed or replaced. B



A

10.INITIALIZE POWER BACK DOOR SYSTEM

B

11.CONFIRMATION TEST
10.INITIALIZE POWER BACK DOOR SYSTEM
a.

Initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST
11.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END