Home › Vehicle Exterior › DOOR / HATCH › POWER BACK DOOR SYSTEM › from 2020.11
RM37A0E _59 Vehicle Exterior _086885 DOOR / HATCH _0418593 POWER BACK DOOR SYSTEM C

DOOR / HATCH  POWER BACK DOOR SYSTEM  B2205  Kick Sensor Circuit  


DESCRIPTION

B2205 is output when the multiplex network door ECU detects that the kick door control sensor is stuck on.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2205 Kick Sensor Circuit One of the following conditions is met for approximately 60 seconds or more:
·

The multiplex network door ECU detects a kick door control sensor short circuit

·

Multiplex network door ECU malfunction

·

Kick door control sensor malfunction


·

Kick door control sensor

·

Multiplex network door ECU

·

Wire harness or connector



WIRING DIAGRAM

B556220E05
4.479,1.979 4.938,2.177 0.458,0.198 10 false W18 1.188,1.969 2.313,2.271 1.125,0.302 10 false V7 2.052,1.115 2.667,1.313 0.615,0.198 10 false KSOT 4.833,1.125 5.448,1.323 0.615,0.198 10 false KSIN 4.552,0.979 4.865,1.177 0.313,0.198 10 false 14 2.542,0.979 2.698,1.177 0.156,0.198 10 false 3 1.198,2.125 3.344,2.323 2.146,0.198 10 false Kick Door Control Sensor 4.469,2.135 6.302,2.385 1.833,0.25 10 false Multiplex Network Door ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting, make sure that the kick door control sensor is not damaged.

·

Before troubleshooting, be sure to read Precautions for Hands Free Power Back Door.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>PRECAUTION

·

If the multiplex network door ECU has been removed and installed or replaced, or if any of the connectors have been disconnected, initialize the power back door system.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>INITIALIZATION

·

After performing work, using the GTS, read the Data List item "Kick Sensor Connection" and check that the kick door control sensor is connected.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST

·

Check the entry and start system (for Entry Function) first before troubleshooting the power back door system.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Back Door > Clear DTCs
50002 159

b.

Recheck for DTCs.

Body Electrical > Back Door > Trouble Codes
50001 159
OK:

DTC B2205 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Disconnect the V7 kick door control sensor connector.


b.

Wait for approximately 60 seconds.


c.

Clear the DTCs.

Body Electrical > Back Door > Clear DTCs
50002 159

d.

Check for DTCs.

Body Electrical > Back Door > Trouble Codes
50001 159
OK:

DTC B2205 is not output.



Result:
Proceed to
OK
NG



OK

REPLACE KICK DOOR CONTROL SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - KICK DOOR CONTROL SENSOR)
3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK DOOR ECU - KICK DOOR CONTROL SENSOR)
a.

Disconnect the W18 multiplex network door ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W18-14 (KSIN) or V7-3 (KSOT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR