If the No. 1 skid control ECU (brake booster with master cylinder assembly) detects an internal sensor (reaction force pressure sensor, accumulator pressure sensor or servo pressure sensor) malfunction during self-diagnosis, DTCs are stored.
Brake pressure sensor "C": Accumulator pressure sensor
Brake pressure sensor "D": Reaction force pressure sensor
Brake pressure sensor "E": Servo pressure sensor
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C057300 | Brake Pressure Sensor "C" Malfunction | Data from the sensor is invalid for 0.8 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C05731F | Brake Pressure Sensor "C" Circuit Intermittent | Fluctuation of the sensor signal exceeds the threshold (7.5 MPa (76.5 kgf/cm2, 1088 psi) or more from the previous value) for 0.1 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C057331 | Brake Pressure Sensor "C" No Signal | Communication with the sensor is invalid for 0.2 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C057396 | Brake Pressure Sensor "C" Component Internal Failure | A malfunction is detected by self-diagnosis function of the sensor. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C057700 | Brake Pressure Sensor "D" Malfunction | Data from the sensor is invalid for 0.2 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C05771F | Brake Pressure Sensor "D" Circuit Intermittent | Fluctuation of the sensor signal exceeds the threshold (7.5 MPa (76.5 kgf/cm2, 1088 psi) or more from the previous value) for 0.1 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C057731 | Brake Pressure Sensor "D" No Signal | Communication with the sensor is invalid for 0.05 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C057796 | Brake Pressure Sensor "D" Component Internal Failure | A malfunction is detected by self-diagnosis function of the sensor. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C05A100 | Brake Pressure Sensor "E" Malfunction | Data from the sensor is invalid for 0.2 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C05A11F | Brake Pressure Sensor "E" Circuit Intermittent | Fluctuation of the sensor signal exceeds the threshold (7.5 MPa (76.5 kgf/cm2, 1088 psi) or more from the previous value) for 0.1 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C05A131 | Brake Pressure Sensor "E" No Signal | Communication with the sensor is invalid for 0.05 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C05A196 | Brake Pressure Sensor "E" Component Internal Failure | A malfunction is detected by self-diagnosis function of the sensor. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C14B016 | Brake Pressure Sensor "D" Power Supply Voltage Circuit Voltage Below Threshold | The supplied voltage to the sensor is less than a certain value for 0.05 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C14B017 | Brake Pressure Sensor "D" Power Supply Voltage Circuit Voltage Above Threshold | The supplied voltage to the sensor is a certain value or more for 0.05 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C14C016 | Servo Pressure Sensor Power Supply Voltage Circuit Voltage Below Threshold | The supplied voltage to the sensor is less than a certain value for 0.05 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C14C017 | Servo Pressure Sensor Power Supply Voltage Circuit Voltage Above Threshold | The supplied voltage to the sensor is a certain value or more for 0.05 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C14D016 | Accumulator Pressure Sensor Power Supply Voltage Circuit Voltage Below Threshold | The supplied voltage to the sensor is less than a certain value for 0.05 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
| C14D017 | Accumulator Pressure Sensor Power Supply Voltage Circuit Voltage Above Threshold | The supplied voltage to the sensor is a certain value or more for 0.05 seconds or more. | No. 1 skid control ECU (brake booster with master cylinder assembly) | Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT