Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C137BA2  Brake System Control Module "A" System Voltage System Voltage Low  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the No. 2 skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits operation of ABS, brake assist, regenerative brake cooperative control, etc.

This DTC is stored when the +BS, IG1 or IG2 terminal voltage meets one of the DTC detection conditions due to a malfunction in the power supply or charging circuit such as the auxiliary battery or DC/DC converter circuit, etc.

This DTC is cleared when the voltage at terminal +BS, IG1 and IG2 returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C137BA2 Brake System Control Module "A" System Voltage System Voltage Low Any of the following is detected:
·

When the voltage at terminal +BS is less than 8.5 V, the master cylinder pressure sensor is invalid for 10 seconds or more.

·

When the voltage at terminal +BS is less than 8.5 V, the brake pedal stroke sensor assembly is invalid for 10 seconds or more.

·

When the voltage at terminal +BS is less than 8.5 V, the wheel cylinder pressure sensor is invalid for 10 seconds or more.

·

When the +BS terminal voltage is below 9.5 V, the power source voltage for all speed sensors is continuously low for 60 seconds or more.

·

When the vehicle speed is 3 km/h (2 mph) or more, the voltage at terminal IG1 or terminal IG2 is excessively low for 10 seconds or more.

·

When the +BS terminal voltage is below 9.5 V and the solenoid relay is ON, the relay contact is OFF continuously for 1.22 seconds or more.

·

When the +BS terminal voltage is below 9.5 V, motor fail-safe relay overcurrent continues for 1.05 seconds or more.


·

Wire harness and connector

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

WIRING DIAGRAM

C427347E01
5.031,0.969 5.479,1.344 0.448,0.375 10 false +BS 5.021,3.281 5.479,3.479 0.458,0.198 10 false GND1 4.74,0.729 5.052,0.927 0.313,0.198 10 false 14 4.802,3.156 5.135,3.323 0.333,0.167 10 false 1 4.844,4.042 6.76,4.479 1.917,0.438 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 4.844,3.875 5.26,4.052 0.417,0.177 10 false A57 3.458,1.01 4.188,1.26 0.729,0.25 10 false ABS NO. 2 1.198,0.813 3.031,1.26 1.833,0.448 10 false from Auxiliary Battery 3.531,0.729 3.844,0.927 0.313,0.198 10 false 1 3.958,0.729 4.271,0.927 0.313,0.198 10 false 2 1.604,1.656 3.271,2.073 1.667,0.417 10 false from IG Circuit 4.74,1.531 5.073,1.729 0.333,0.198 10 false 45 5.042,1.781 5.49,2.063 0.448,0.281 10 false IG1 3.313,2.625 4.375,2.958 1.063,0.333 10 false ECU-IG2 NO. 3 3.958,1.542 4.271,1.74 0.313,0.198 10 false 2 3.531,1.531 3.844,1.729 0.313,0.198 10 false 1 5.042,2.583 5.49,2.865 0.448,0.281 10 false IG2 4.74,2.344 5.073,2.542 0.333,0.198 10 false 15 3.302,1.823 4.365,2.156 1.063,0.333 10 false ECU-IG2 NO. 3 3.958,2.344 4.271,2.542 0.313,0.198 10 false 2 3.531,2.344 3.844,2.542 0.313,0.198 10 false 1 1.604,2.458 3.271,2.875 1.667,0.417 10 false from IG Circuit 6.01,1.656 6.323,1.854 0.313,0.198 10 false IC

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before performing troubleshooting, make sure to confirm that the auxiliary battery voltage is normal.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.READ VALUE USING GTS (IG1 VOLTAGE, IG2 VOLTAGE AND BS VOLTAGE)
a.

Using the GTS, monitor the voltage values of IG1 voltage, IG2 voltage, and BS voltage.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG1 Voltage IG1 voltage value Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to auxiliary battery voltage
IG2 Voltage IG2 voltage value Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to auxiliary battery voltage
BS Voltage +BS voltage value Min.: 0.000 V
Max.: 20.000 V
- Changes in proportion to auxiliary battery voltage
Chassis > Brake/EPB > Data List
Tester Display
IG1 Voltage
IG2 Voltage
BS Voltage
50003 435 296,297,298

Result:
Result Proceed to
IG1 voltage value is below 11 V. A
IG2 voltage value is below 11 V. B
BS voltage value is below 11 V. C
IG1 voltage, IG2 voltage and BS voltage values are below 11 V. D
IG1 voltage, IG2 voltage and BS voltage values are 11 to 14 V. E



A

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

B

5.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)

C

6.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

D

7.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

E

2.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C425607C08
1.49,0.479 1.927,0.729 0.438,0.25 2.51,2.792 2.365,2.219 true 1.594,0.521 2.052,0.719 0.458,0.198 10 false A57 0.135,0.135 0.49,0.5 0.354,0.365 10 false *a 2.458,2.823 2.854,3.094 0.396,0.271 10 false IG1
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-45 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Reconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC C137BA2 is not output. A
DTC C137BA2 is output. B



A

B

5.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.
C425607C09
1.49,0.479 1.927,0.729 0.438,0.25 0.667,2.698 1.01,2.063 true 1.594,0.521 2.052,0.719 0.458,0.198 10 false A57 0.135,0.135 0.49,0.5 0.354,0.365 10 false *a 0.542,2.729 0.938,3 0.396,0.271 10 false IG2
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-15 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
C425607C02
1.49,0.479 1.927,0.729 0.438,0.25 2.635,1.656 2.375,1.01 true 1.594,0.521 2.052,0.719 0.458,0.198 10 false A57 0.135,0.135 0.49,0.5 0.354,0.365 10 false *a 2.208,0.813 2.604,1.083 0.396,0.271 10 false +BS
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-1 (GND1) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR