Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for HV Model RHD) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0449071 BRAKE ACTUATOR(for HV Model RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for HV Model RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of brake actuator assembly
1.

Bleed air

2.

Perform "Calibration"


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned to ON (Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.



PROCEDURE

Hide 1.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

Hide 2.REMOVE FRONT WHEEL LH

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53808A 5.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 6.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 7.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 8.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 9.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 10.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 55704B 11.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 12.REMOVE BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY

a.
C447841

Disconnect the engine room main wire from the brake booster with accumulator pump assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C447693C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the engine room main wire from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



c.
C447694C01
1.958,0.625 2.156,0.375 true 1.75,0.865 1.813,1.208 true 1.458,1.719 1.656,1.469 true 1.229,1.375 1.521,0.958 true 1.01,0.906 1.302,0.75 true 2.25,1.167 2.583,0.75 2.583,0.75 2.833,0.75 true 2.875,0.656 3.083,0.833 0.208,0.177 10 true *b 1.344,1.74 1.521,1.927 0.177,0.188 10 true *a 0.771,0.833 0.99,1.01 0.219,0.177 10 true *c 1.083,1.396 1.292,1.573 0.208,0.177 10 true *d 1.75,1.24 1.958,1.417 0.208,0.177 10 true *e 2.177,0.281 2.354,0.448 0.177,0.167 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Disc Brake Cylinder Assembly RH
*d To Front Disc Brake Cylinder Assembly LH
*e To Rear Disc Brake Cylinder Assembly RH
*f To Rear Disc Brake Cylinder Assembly LH


Use tags or make a memo to identify the places to reconnect the brake lines.


d.
C447695

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




e.
C447700

Using a union nut wrench, disconnect the brake line while holding the front flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




f.
C447696

Remove the bolt and disengage the 5 clamps to remove the brake line from the No. 4 brake tube clamp.

NOTICE:

Do not kink or damage the brake lines.



g.
C447697

Disengage the 5 clamps to remove the brake line from the No. 1 brake tube clamp.

NOTICE:

Do not kink or damage the brake lines.



h.
C447698

Disengage the 2 clamps to remove the brake line from the No. 12 brake tube clamp.

NOTICE:

Do not kink or damage the brake lines.



i.
C447699

Disengage the clamp to separate the brake line.

NOTICE:

Do not kink or damage the brake line.



j.
C447701

Move aside the brake line as shown in the illustration.

NOTICE:

Do not apply excessive force to the brake line.



k.
C447702

Disengage the clamp to remove the No. 10 brake tube clamp.


l.
C447703

Remove the bolt.


m.

Using a union nut wrench, disconnect the brake line from the brake booster with accumulator pump assembly.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




n.
C447704

Remove the 2 bolts and nut to separate the brake actuator with brake booster pump assembly from the vehicle body.


o.
C447705

Slide the clip and disconnect the No. 2 brake actuator hose from the brake booster with accumulator pump assembly.


p.

Remove the brake actuator with brake booster pump assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Hold the brake actuator with brake booster pump assembly by the brake actuator bracket assembly.



HINT:

Remove the brake actuator with brake booster pump assembly while avoiding the brake lines.



Hide 47070B 13.REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

Hide 44510 14.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C447710

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
C447709

Do not hold the brake actuator assembly by the connector.



Hide 44521B 15.REMOVE NO. 2 BRAKE ACTUATOR CASE COLLAR

HINT:

Perform this procedure only when replacement of the No. 2 brake actuator case collars is necessary.


a.
C447711

Remove the 3 nuts and separate the upper brake actuator bracket from the lower brake actuator bracket.


b.
C447712

Remove the 3 No. 2 brake actuator case collars from the brake actuator bracket cushion.


Hide 44547B 16.REMOVE BRAKE ACTUATOR BRACKET CUSHION

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.


a.
C447713

Remove the 3 brake actuator bracket cushions from the lower brake actuator bracket.