Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C13B951  SM Valve Learning Not Programmed  C13B954  SM Valve Learning Missing Calibration  


DESCRIPTION

The No. 2 skid control ECU (brake actuator assembly) stores the individual characteristics of each linear solenoid built into the brake actuator assembly. Based on the stored information, the No. 2 skid control ECU (brake actuator assembly) calibrates the individual differences and controls systems.

The No. 2 skid control ECU (brake actuator assembly) receives the shift position P signal from the hybrid vehicle control ECU through the CAN communication system.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C13B951 SM Valve Learning Not Programmed The SM solenoid valve offset learning value is not stored.
·

If this DTC is not output after performing SM solenoid valve offset learning, there is no malfunction.

·

Brake fluid leaks

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)
HINT:

During Dealer Mode, related DTCs are cleared.


C13B954 SM Valve Learning Missing Calibration SM solenoid valve offset learning cannot be obtained
·

If this DTC is not output after performing SM solenoid valve offset learning, there is no malfunction.

·

Brake fluid leaks

·

No. 2 skid control ECU (brake actuator assembly)


Output ECU: No. 2 skid control ECU (brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CHECK DTC
a.

Check that no DTCs other than those related to incomplete learning are output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435
OK:

DTCs other than those related to incomplete learning are not output.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR FLUID LEAK

NG

2.CHECK FOR FLUID LEAK
a.

Inspect the following items for brake fluid leaks:

·

The brake lines from the brake booster with master cylinder assembly to each wheel cylinder.

·

The main body of the brake booster with master cylinder assembly and brake actuator assembly.


OK:

There are no fluid leaks.



Result:
Proceed to
OK
NG



OK

3.PERFORM AIR BLEEDING

NG

REPAIR OR REPLACE APPLICABLE PART

3.PERFORM AIR BLEEDING
a.

Perform the air bleeding procedure in Bleed Brake System.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING


Result:
Proceed to
NEXT



NEXT

4.PERFORM SM SOLENOID VALVE OFFSET LEARNING
4.PERFORM SM SOLENOID VALVE OFFSET LEARNING
a.

Check that the conditions required for SM solenoid valve offset learning are met and perform SM solenoid valve offset learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

NOTICE:

If DTC C13B954 is output, wait 4 minutes or more with the ignition switch turned off, then perform learning after turning the ignition switch to ON and clearing the DTCs.


Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554
1.

The auxiliary battery voltage is 11 to 15.5 V when the ignition switch is turned ON (READY).

2.

The brake actuator assembly is not hot.

3.

The hybrid control system is not malfunctioning.

4.

The shift state indicator shows that the shift lever is in P.

5.

The READY light in the combination meter assembly is illuminated.

6.

The brake pedal is not depressed.

7.

The parking brake is released.

8.

DTC C134551 is not output.



Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs C13B951 and C13B954 are not output. A
DTCs C13B951 and/or C13B954 are output. B



A

B