The solenoid relay and master cylinder cut solenoid valves are built into the brake actuator assembly.
The master cylinder cut solenoid valves control the brake fluid pressure from the pump motor in the brake actuator assembly and output brake fluid pressure in accordance with operation of the system.
When these DTCs are stored, the fail-safe function operates and the solenoid relay is turned off to prevent the master cylinder cut solenoid valves from operating.
Brake pressure control solenoid "A": Solenoid SM1
Brake pressure control solenoid "B": Solenoid SM2
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C13C012 | Brake Pressure Control Solenoid "A" Control Circuit Short to Battery | An excessive current is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13C014 | Brake Pressure Control Solenoid "A" Control Circuit Short to Ground or Open | Insufficient current is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13C018 | Brake Pressure Control Solenoid "A" Control Circuit Current Below Threshold | An open is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13C019 | Brake Pressure Control Solenoid "A" Control Circuit Current Above Threshold | Overcurrent is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13C01D | Brake Pressure Control Solenoid "A" Control Circuit Current Out of Range | Current leakage is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13C912 | Brake Pressure Control Solenoid "B" Control Circuit Short to Battery | An excessive current is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13C914 | Brake Pressure Control Solenoid "B" Control Circuit Short to Ground or Open | Insufficient current is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13C918 | Brake Pressure Control Solenoid "B" Control Circuit Current Below Threshold | An open is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13C919 | Brake Pressure Control Solenoid "B" Control Circuit Current Above Threshold | Overcurrent is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C13C91D | Brake Pressure Control Solenoid "B" Control Circuit Current Out of Range | Current leakage is detected in the solenoid for 0.05 seconds or more. | No. 2 skid control ECU (brake actuator assembly) | Output ECU: No. 2 skid control ECU (brake actuator assembly) |
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT