Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  P057100  Brake Switch "A"  


DESCRIPTION

The No. 1 skid control ECU (brake booster with master cylinder assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.

The No. 1 skid control ECU (brake booster with master cylinder assembly) incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
P057100 Brake Switch "A" An open in the stop light switch circuit continues for 10 seconds or more.
·

Wire harness and connector

·

Stop light switch assembly

·

STP circuit

·

No. 1 skid control ECU (brake booster with master cylinder assembly)


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

WIRING DIAGRAM

C427342E01
4.833,0.594 6.917,0.958 2.083,0.365 10 false to No. 2 Skid Control ECU (Brake Actuator Assembly) 5.302,3.896 5.917,4.094 0.615,0.198 10 false STP 5.042,3.646 5.656,3.844 0.615,0.198 10 false 37 4.698,4.323 5.313,4.521 0.615,0.198 10 false A44 4.698,4.51 7.125,4.885 2.427,0.375 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.688,5.208 5.01,5.573 1.323,0.365 10 false to Stop Light Circuit 3.552,0.479 4.167,0.677 0.615,0.198 10 false 3 3.563,1.5 4.177,1.698 0.615,0.198 10 false 4 3.552,3.646 4.167,3.844 0.615,0.198 10 false 1 3.146,3.896 3.76,4.094 0.615,0.198 10 false OUT 3.146,1.75 3.76,1.948 0.615,0.198 10 false ACC 3.333,0.76 3.521,0.979 0.188,0.219 10 false L 1.594,0.854 1.885,1.083 0.292,0.229 10 false 7 1.781,1.104 2.052,1.396 0.271,0.292 10 false B 1.594,3.646 1.844,3.844 0.25,0.198 10 false 2 1.781,3.896 2.396,4.094 0.615,0.198 10 false GND 1.74,4.219 2.052,4.438 0.313,0.219 10 false A42 1.729,4.375 3.521,4.583 1.792,0.208 10 false Stop Light Switch Assembly 0.844,1.156 1.281,1.354 0.438,0.198 10 false STOP 0.771,0.844 0.948,1.042 0.177,0.198 10 false 1 1.229,0.854 1.438,1.021 0.208,0.167 10 false 2 0.833,1.615 1.708,1.917 0.875,0.302 10 false from Auxiliary Battery 4.833,1.615 6.917,1.979 2.083,0.365 10 false to No. 2 Skid Control ECU (Brake Actuator Assembly) 4.833,2.615 6.917,2.979 2.083,0.365 10 false to No. 2 Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.


Result:
Result Proceed to
All stop lights illuminate when the brake pedal is depressed and turn off when the brake pedal is released. A
All stop lights do not illuminate when the brake pedal is depressed. B
One or more stop lights illuminate when the brake pedal is depressed but remain on when the brake pedal is released. C



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)

C

6.CHECK STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Check the value of Stop Light SW when the brake pedal is depressed.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly (STP terminal input) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:

The brake pedal state is determined using the voltage at terminal STP


Chassis > Brake Booster > Data List
Tester Display
Stop Light SW
50003 466 59

Result:
Result Proceed to
The value of Stop Light SW is ON. A
Other than above. B



A

3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION

B

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION
a.
C401043C74
0.417,0.656 0.76,0.885 0.344,0.229 2.417,1.646 2.167,1.063 true 0.469,0.677 0.927,0.875 0.458,0.198 10 false A42 0.188,0.188 0.646,0.385 0.458,0.198 10 false *a 2.313,1.677 2.771,1.875 0.458,0.198 10 false OUT
*a Component with harness connected
(Stop Light Switch Assembly)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (OUT) - Body ground
·

Ignition switch ON

·

The headlights are on

·

The blower motor switch is in the HI position

·

The rear window defogger is turned on

·

Stop light switch assembly off (Brake pedal released)


Below 1.5 V



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

6.CHECK STOP LIGHT SWITCH ASSEMBLY
4.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
DTC P057100 is not output. A
DTC P057100 is output. B



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

6.CHECK STOP LIGHT SWITCH ASSEMBLY
a.
C401044C80
0.49,0.646 0.833,0.854 0.344,0.208 1.26,1.25 1.115,1.677 true 0.25,0.198 0.563,0.354 0.313,0.156 10 false *a 0.542,0.667 1,0.885 0.458,0.219 10 false A42 0.979,1.708 1.396,1.906 0.417,0.198 10 false OUT
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A42 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (OUT) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

7.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
7.CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
a.
C401044C80
0.49,0.646 0.833,0.854 0.344,0.208 1.26,1.25 1.115,1.677 true 0.25,0.198 0.563,0.354 0.313,0.156 10 false *a 0.542,0.667 1,0.885 0.458,0.219 10 false A42 0.979,1.708 1.396,1.906 0.417,0.198 10 false OUT
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (OUT) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

8.CHECK FOR SHORT TO +B IN STP CIRCUIT
8.CHECK FOR SHORT TO +B IN STP CIRCUIT
a.

Check that there is no short to +B in the STP circuit (wire harnesses, connectors, ECUs and stop lights).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C423268C05
0.417,0.719 0.833,0.969 0.417,0.25 1.813,2.74 1.948,2.156 true 1.677,2.771 2.135,2.969 0.458,0.198 10 false STP 0.49,0.76 0.948,0.958 0.458,0.198 10 false A44 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-37 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)
a.

Check that there is no open in the wire harnesses and connectors from terminal OUT of the stop light switch assembly to the stop lights.

OK:

No open.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR