Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  Abnormal Brake Pedal Response on First Depression  


DESCRIPTION

If the vehicle has been stopped without opening or closing the driver door for a long period of time, the electronically controlled brake system will not be ready and sufficient fluid pressure may not be stored in the accumulator. In this case, the brake pedal response may not be the same as usual the first time the brake pedal is depressed. This is not a malfunction.

WIRING DIAGRAM

C453588E01
5.104,1.781 5.417,1.979 0.313,0.198 10 false 40 5.365,2.083 5.75,2.302 0.385,0.219 10 false CTY 0.417,0.917 2.25,1.323 1.833,0.406 10 false to Main Body ECU (Multiplex Network Body ECU) 2.948,1.802 3.26,2 0.313,0.198 10 false 1 1.135,2.156 1.583,2.396 0.448,0.24 10 false M47 1.135,2.333 4.104,2.604 2.969,0.271 10 false Front Door Courtesy Light Switch Assembly LH 4.688,3.854 5,4.052 0.313,0.198 10 false A44 4.688,4.031 7.115,4.469 2.427,0.438 10 false No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly) 3.479,1.813 3.792,2.01 0.313,0.198 10 false *1 0.438,2.219 0.75,2.417 0.313,0.198 10 false *1 1.135,3.552 4.104,3.823 2.969,0.271 10 false Front Door Courtesy Light Switch Assembly RH 1.135,3.365 1.583,3.604 0.448,0.24 10 false M3 2.948,2.958 3.26,3.156 0.313,0.198 10 false 1 3.479,2.969 3.792,3.167 0.313,0.198 10 false *2 0.448,3.375 0.76,3.573 0.313,0.198 10 false *2 0.75,4.354 1.708,4.583 0.958,0.229 10 false *1: for LHD 1.719,4.354 2.677,4.583 0.958,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.BRAKE PROBLEM CHECK
a.

Check the conditions at the time the problem occurred.

i.

Whether a warning light illuminated or the buzzer sounded.


ii.

The number of times the ignition switch was turned to ON since the latest symptom occurred.


iii.

Frequency of the symptom.



Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC
a.

Check the DTCs (electronically controlled brake system) that are output.

Chassis > Brake Booster > Trouble Codes
50001 466

Result:
Result Proceed to
DTCs C125600 and C139100 are not output. A
DTCs C125600 and/or C139100 are output. B



A

3.CHECK VEHICLE

B

3.CHECK VEHICLE
a.

Turn the ignition switch off.


b.

Depress the brake pedal within 4 minutes of opening the driver door and check the response of the brake pedal.


c.

Release the brake pedal and wait for 4 minutes without depressing the brake pedal, opening or closing the driver door or operating the ignition switch.


d.

After 4 minutes or more have elapsed, depress the brake pedal and check that the first depression response is different to successive depression responses.

HINT:

Compare the response of the brake pedal when the system is in sleep mode and when the stroke simulator is operating.



Result:
Result Proceed to
The response of the brake pedal does not change. A
The response of the brake pedal changed. B



A

4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR DRIVER SIDE)

B

END

4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR DRIVER SIDE)
a.

Set the interior light door switch to ON and check that the map light assembly illuminates, then set the interior light door switch to DOOR.


b.

Check that the map light assembly illuminates when the driver door is opened.

OK:

The map light assembly illuminates when the driver door is opened.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)

NG

INSPECT LIGHTING SYSTEM (COURTESY LIGHT SWITCH CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)
a.
C423268C14
0.438,0.698 0.844,0.979 0.406,0.281 2.385,2.771 2.26,2.156 true 2.281,2.792 2.74,2.99 0.458,0.198 10 false CTY 0.521,0.75 0.979,0.948 0.458,0.198 10 false A44 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 1 Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A44-40 (CTY) - Body ground Driver door open Below 1.5 V
A44-40 (CTY) - Body ground Driver door closed 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR