These DTCs are stored when a malfunction occurs in the navigation antenna assembly*1 or antenna divider*2.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | GPS Antenna Connection Malfunction(short) | Navigation antenna malfunction | ·
Navigation antenna assembly*1 ·
No. 2 antenna cord sub-assembly*1 ·
Antenna divider*2 ·
Antenna cord sub-assembly*2 ·
Radio and display receiver assembly |
| B15C1 | GPS Antenna Connection Malfunction(break) | Navigation antenna power source malfunction | ·
Navigation antenna assembly*1 ·
No. 2 antenna cord sub-assembly*1 ·
Antenna divider*2 ·
Antenna cord sub-assembly*2 ·
Radio and display receiver assembly |
*1: w/o Heated Windshield Defroster System
*2: w/ Heated Windshield Defroster System
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION
Check that the No. 2 antenna cord sub-assembly*1 or antenna cord sub-assembly*2 is properly installed and does not have any sharp bends, pinching or loose connections before performing the following procedure.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
*1: w/o Heated Windshield Defroster System
*2: w/ Heated Windshield Defroster System
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Heated Windshield Defroster System) | B |
| NG (w/ Heated Windshield Defroster System) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Remove the No. 2 antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Component without harness connected
(No. 2 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 - B-1 | Always | Below 1 Ω |
| A-3a - B-1a | Always | Below 1 Ω |
| A-3 or B-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Inspect the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
| *a | Component without harness connected
(Antenna Divider) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 6 | Always | 10 kΩ or higher |
| 2 - 2a | Always | 243 to 267 Ω |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Component without harness connected
(Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I-2 - B-1 | Always | Below 1 Ω |
| I-2a - B-1a | Always | Below 1 Ω |
| I-2 or B-1 - Body ground | Always | 10 kΩ or higher |
| I-2a or B-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the antenna divider with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG