| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| C060E19 | Left Electric Parking Brake Actuator Circuit Current Above Threshold | When the electric parking brake is operating, overcurrent is detected in the parking brake actuator assembly LH 3 times. | ·
Parking brake actuator assembly LH ·
No. 2 parking brake wire assembly ·
Wire harness and connector ·
No. 2 skid control ECU (brake actuator assembly) |
DTC stored | An electric parking brake system malfunction is displayed on the multi-information display. |
To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the No. 2 skid control ECU (brake actuator assembly), perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".
When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the uM2 and u2 No. 2 parking brake wire assembly connectors.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of No. 2 Parking Brake Wire Assembly | *b | (to wire harness connector) |
| *c | (to Parking Brake Actuator Assembly LH) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM2-1 - u2-2 (+) | Always | Below 1 Ω |
| uM2-1 or u2-2 (+) - Body ground and other terminals | Always | 10 kΩ or higher |
| uM2-2 - u2-1 (-) | Always | Below 1 Ω |
| uM2-2 or u2-1 (-) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure the No. 2 parking brake wire assembly is securely installed.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Disconnect the u2 parking brake actuator assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-3 (MRL+) - u2-2 (+) | Always | Below 1 Ω |
| A57-3 (MRL+) or u2-2 (+) - Body ground | Always | 10 kΩ or higher |
| A57-2 (MRL-) - u2-1 (-) | Always | Below 1 Ω |
| A57-2 (MRL-) or u2-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking brake actuator assembly LH.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>REMOVAL
Inspect the parking brake actuator assembly LH.
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure the No. 2 parking brake wire assembly is securely installed.
Disconnect the u2 parking brake actuator assembly LH connector.
| *a | Front view of No. 2 Parking Brake Wire Assembly
(to Parking Brake Actuator Assembly LH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| u2-2 (+) - u2-1 (-) | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the uM2 No. 2 parking brake wire assembly connector.
| *a | Front view of wire harness connector
(to No. 2 Parking Brake Wire Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM2-1 - uM2-2 | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the uM2 No. 2 parking brake wire assembly connector.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector | *b | (to No. 2 Skid Control ECU (Brake Actuator Assembly)) |
| *c | (to No. 2 Parking Brake Wire Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| uM2-1 or A57-3 (MRL+) - Body ground | Always | Below 1 V |
| uM2-2 or A57-2 (MRL-) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model RHD)>REMOVAL
NG