Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086873 PARKING BRAKE _0420958 ELECTRIC PARKING BRAKE SYSTEM(for HV Model) J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model)  Electric Parking Brake does not Operate  


WIRING DIAGRAM

C427566E01
0.458,0.719 1.688,0.917 1.229,0.198 10 false ABS NO. 2 0.354,1.313 1.583,1.51 1.229,0.198 10 false ECU-IG2 NO. 3 2.833,1.552 3.177,1.771 0.344,0.219 10 false A57 5.135,1.313 7.01,1.792 1.875,0.479 10 false Combination Meter Assembly 2.833,1.698 4.583,2.458 1.75,0.76 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 2.802,0.542 4.031,0.74 1.229,0.198 10 false +BS 2.813,1.146 4.042,1.344 1.229,0.198 10 false IG1 2.552,0.458 2.927,0.677 0.375,0.219 10 false 14 2.552,1.052 2.927,1.271 0.375,0.219 10 false 45 0.917,3.219 3.344,3.719 2.427,0.5 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the No. 2 skid control ECU (brake actuator assembly), perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

·

When replacing the No. 2 skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



HINT:

Even if the electric parking brake is operating normally, the parking brake indicator light (red) on the combination meter may be malfunctioning.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.VEHICLE OPERATION CHECK

B

2.VEHICLE OPERATION CHECK
a.

When the vehicle's tires are lifted off the ground and the GTS is used to operate the electric parking brake, check the condition of the rear tires.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Lock and release operation is normal and parking brake indicator light turns off or blinks (red) A
Lock and release operation is malfunctioning and parking brake indicator light illuminates (red) or turns off according to switch operation B
Lock and release operation is malfunctioning and parking brake indicator light turns off or blinks (red) C



A

3.INSPECT COMBINATION METER ASSEMBLY

B

INSPECT REAR BRAKE

C

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
3.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Park
50004 122 69

b.

Check the combination meter assembly.

OK:

Parking brake indicator light (red) turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (+BS TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.
C342413C23
1.458,0.125 1.875,0.375 0.417,0.25 2.969,1.813 2.698,0.99 true 1.552,0.167 2.01,0.365 0.458,0.198 10 false A57 2.896,1.854 3.354,2.052 0.458,0.198 10 false +BS 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-14 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)
a.

Turn the ignition switch off.


b.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


c.
C342413C22
1.458,0.125 1.875,0.375 0.417,0.25 2.5,1.823 2.365,1.354 true 1.552,0.167 2.01,0.365 0.458,0.198 10 false A57 2.458,1.844 2.917,2.042 0.458,0.198 10 false IG1 0.104,0.104 0.563,0.302 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-45 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR