Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for Gasoline Model RHD) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0449072 BRAKE ACTUATOR(for Gasoline Model RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for Gasoline Model RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of brake actuator assembly Perform "Calibration"
·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned to ON (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 1.REMOVE BATTERY

Hide 55704B 2.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 3.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 4.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 74404B 5.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 6.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C447475C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the engine room main wire from the brake actuator assembly as shown in the illustration.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C447476C01
0.99,0.135 1.323,0.135 1.323,0.135 1.573,0.5 true 1.927,0.635 2.208,0.302 2.208,0.302 2.458,0.302 true 2.469,0.833 2.635,0.583 2.635,0.583 2.969,0.583 true 2.083,1.844 2.083,1.427 true 1.156,1.302 1.49,1.052 true 1.583,1.385 1.667,0.969 true 3,0.49 3.188,0.667 0.188,0.177 10 true *a 2,1.854 2.188,2.042 0.188,0.188 10 true *b 0.958,1.24 1.135,1.417 0.177,0.177 10 true *c 1.49,1.406 1.667,1.573 0.177,0.167 10 true *d 0.813,0.052 0.979,0.229 0.167,0.177 10 true *e 2.5,0.198 2.667,0.365 0.167,0.167 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Disc Brake Cylinder Assembly LH
*d To Rear Disc Brake Cylinder Assembly RH
*e To Rear Disc Brake Cylinder Assembly LH
*f To Front Disc Brake Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake lines.


c.
C447477

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




d.
C447478

Disengage the clamp to separate the brake line.

NOTICE:

Do not kink or damage the brake line.



e.
C447479

Disengage the clamp to remove the brake tube clamp.


f.
C447480

Remove the 2 bolts, nut and brake actuator with bracket.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Hold the brake actuator with bracket by the brake actuator bracket assembly.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



Hide 44510 7.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C447481

Remove the 3 bolts and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
C447709

Do not hold the brake actuator assembly by the connector.



Hide 44521B 8.REMOVE NO. 2 BRAKE ACTUATOR CASE COLLAR

HINT:

Perform this procedure only when replacement of the No. 2 brake actuator case collars is necessary.


a.
C447482

Remove the 3 nuts and upper brake actuator bracket.


b.

Remove the 3 No. 2 brake actuator case collars from the brake actuator bracket cushion.


Hide 44547B 9.REMOVE BRAKE ACTUATOR BRACKET CUSHION

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.


a.
C447483

Remove the 3 brake actuator bracket cushions from the lower brake actuator bracket.