Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0420942 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model)  P057113  Brake Switch "A" Circuit Open  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.

The skid control ECU incorporates a circuit to detect an open circuit.

This DTC is output when an open circuit is detected in the stop light signal input line.

DTC No. Detection Item DTC Detection Condition Trouble Area
P057113 Brake Switch "A" Circuit Open When the +BS terminal voltage is 9.5 V or more, an open is detected in the STP terminal circuit for 0.3 seconds or more and the stop light drive output (STPO) is off for 0.1 seconds or more.
·

Wire harness and connector

·

Skid control ECU (Brake actuator assembly)

·

Stop light switch assembly

·

STP circuit



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model)>UTILITY



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed.


Result:
Result Proceed to
All stop lights illuminate when the brake pedal is depressed and turn off when the brake pedal is released. A
All stop lights do not illuminate when the brake pedal is depressed. B
One or more stop lights illuminate when the brake pedal is depressed but remain on when the brake pedal is released. C



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)

C

6.CHECK STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Check the value of Stop Light SW when the brake pedal is depressed.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly status
(STP or STP2 terminal input)
OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:
·

Stop light control relay off: STP terminal status displayed.

·

Stop light control relay on: STP2 terminal status displayed.



Chassis > Brake/EPB > Data List
Tester Display
Stop Light SW
50003 435 59

Result:
Result Proceed to
The value of Stop Light SW is ON. A
Other than above. B



A

3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION

B

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.STOP LIGHT SWITCH ASSEMBLY OUTPUT CIRCUIT INSPECTION
a.
C401043C74
0.417,0.656 0.76,0.885 0.344,0.229 2.417,1.646 2.167,1.063 true 0.469,0.677 0.927,0.875 0.458,0.198 10 false A42 0.188,0.188 0.646,0.385 0.458,0.198 10 false *a 2.313,1.677 2.771,1.875 0.458,0.198 10 false OUT
*a Component with harness connected
(Stop Light Switch Assembly)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (OUT) - Body ground
·

Ignition switch ON

·

The headlights are on

·

The blower motor switch is in the HI position

·

The rear window defogger is turned on

·

Stop light switch assembly off (Brake pedal released)


Below 1.5 V



Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

6.CHECK STOP LIGHT SWITCH ASSEMBLY
4.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.RECONFIRM DTC
5.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTC P057113 is not output. A
DTC P057113 is output. B



A

B

6.CHECK STOP LIGHT SWITCH ASSEMBLY
a.
C401044C80
0.49,0.646 0.833,0.854 0.344,0.208 1.26,1.25 1.115,1.677 true 0.25,0.198 0.563,0.354 0.313,0.156 10 false *a 0.542,0.667 1,0.885 0.458,0.219 10 false A42 0.979,1.708 1.396,1.906 0.417,0.198 10 false OUT
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A42 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (OUT) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

7.CHECK BRAKE ACTUATOR ASSEMBLY
7.CHECK BRAKE ACTUATOR ASSEMBLY
a.
C401044C80
0.49,0.646 0.833,0.854 0.344,0.208 1.26,1.25 1.115,1.677 true 0.25,0.198 0.563,0.354 0.313,0.156 10 false *a 0.542,0.667 1,0.885 0.458,0.219 10 false A42 0.979,1.708 1.396,1.906 0.417,0.198 10 false OUT
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-1 (OUT) - Body ground Stop light switch assembly off
(Brake pedal released)
Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

8.CHECK FOR SHORT TO +B IN STP CIRCUIT
8.CHECK FOR SHORT TO +B IN STP CIRCUIT
a.

Check that there is no short to +B in the STP circuit (wire harnesses, connectors and stop lights).

OK:

No short to +B.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PART

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C343081C58
1.49,0.146 1.854,0.406 0.365,0.26 2.021,0.938 2.406,0.396 true 1.552,0.188 2.01,0.385 0.458,0.198 10 false A39 0.167,0.188 0.625,0.385 0.458,0.198 10 false *a 2.292,0.229 2.75,0.427 0.458,0.198 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-11 (STP) - Body ground Stop light switch assembly on
(Brake pedal depressed)
11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT)
a.

Check that there is no open in the wire harnesses and connectors from terminal OUT of the stop light switch assembly to the stop lights.

OK:

No open.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR