When the position control ECU assembly (driver seat) does not receive a slide motor position sensor signal despite the seat having been moved forward or backward by power seat motor operation, this DTC is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2650 | Slide Sensor Malfunction | Slide motor position sensor signal not received when power seat moved forward or backward | ·
Position control ECU assembly (driver seat) ·
Slide motor (Separate type front seat cushion spring assembly (driver seat)) ·
Wire harness or connector |
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B2650 is not output.
| Result | Proceed to |
|---|---|
| DTC B2650 is not output | A |
| DTC B2650 output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Tester Display |
|---|
| Seat Slide Operation |
Slide motor operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e11*1 or e28*2 slide motor (separate type front seat cushion spring assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e11-2 - e11-3 | Slide switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e28-2 - e28-3 | Slide switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Component with harness connected
(Slide Motor (Separate Type Front Seat Cushion Spring Assembly (Driver Seat))) |
Reconnect the e11*1 or e28*2 slide motor (separate type front seat cushion spring assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e11-2 - Body ground | Slide motor operating | 4.5 to 4.8 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e28-2 - Body ground | Slide motor operating | 4.5 to 4.8 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e25 position control ECU assembly (driver seat) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-26 (SSRS) - e11-2 | Always | Below 1 Ω |
| e25-26 (SSRS) or e11-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - e11-3 | Always | Below 1 Ω |
| e25-12 (SGND) or e11-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-26 (SSRS) - e28-2 | Always | Below 1 Ω |
| e25-26 (SSRS) or e28-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - e28-3 | Always | Below 1 Ω |
| e25-12 (SGND) or e28-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e23 position control ECU assembly (driver seat) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-1 (SLD+) - e11-4 | Always | Below 1 Ω |
| e23-1 (SLD+) or e11-4 - Body ground | Always | 10 kΩ or higher |
| e23-5 (SLD-) - e11-1 | Always | Below 1 Ω |
| e23-5 (SLD-) or e11-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e23-1 (SLD+) - e28-4 | Always | Below 1 Ω |
| e23-1 (SLD+) or e28-4 - Body ground | Always | 10 kΩ or higher |
| e23-5 (SLD-) - e28-1 | Always | Below 1 Ω |
| e23-5 (SLD-) or e28-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG