Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › from 2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420115 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2653  Lifter Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a lifter motor position sensor signal despite the seat having been moved upward or downward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2653 Lifter Sensor Malfunction Lifter motor position sensor signal not received when power seat moved upward or downward
·

Position control ECU assembly (driver seat)

·

Lifter motor (power seat lifter motor assembly (driver seat))

·

Wire harness or connector



WIRING DIAGRAM

B605540E04
0.802,2.49 1.781,2.76 0.979,0.271 10 false e13*1, e30*2 4.802,1.063 5.26,1.26 0.458,0.198 10 false e24 4.813,0.542 5.271,0.74 0.458,0.198 10 false e23 4.802,2.083 5.26,2.281 0.458,0.198 10 false e25 4.802,1.573 5.26,1.771 0.458,0.198 10 false e25 5.219,0.542 5.833,0.74 0.615,0.198 10 false LFT+ 5.219,1.052 5.833,1.25 0.615,0.198 10 false LFT- 5.229,1.563 5.844,1.76 0.615,0.198 10 false SSRL 5.229,2.083 5.844,2.281 0.615,0.198 10 false SGND 0.802,2.646 2.667,3.417 1.865,0.771 10 false Lifter Motor (Power Seat Lifter Motor Assembly (Driver Seat)) 4.75,2.594 6.708,3.135 1.958,0.542 10 false Position Control ECU Assembly (Driver Seat) 4.885,0.313 5.042,0.51 0.156,0.198 10 false 6 4.896,0.823 5.052,1.021 0.156,0.198 10 false 5 4.844,1.333 5.156,1.531 0.313,0.198 10 false 25 4.833,1.844 5.146,2.042 0.313,0.198 10 false 12 2.323,1.458 3.073,1.75 0.75,0.292 10 false 2 2.323,0.438 3.177,0.802 0.854,0.365 10 false 1 2.313,0.958 3.156,1.365 0.844,0.406 10 false 4 2.313,1.979 3.198,2.25 0.885,0.271 10 false 3 4.823,3.271 5.802,3.542 0.979,0.271 10 false *1: for LHD 5.594,3.26 6.573,3.531 0.979,0.271 10 false *2: for RHD

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2653 is not output.



Result:
Result Proceed to
DTC B2653 is not output A
DTC B2653 output B



A

B

3.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
3.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Lifter Operation Seat lifter operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
OK:

Lifter motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)

NG

7.INSPECT LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)
a.

Disconnect the e13*1 or e30*2 lifter motor (power seat lifter motor assembly (driver seat)) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
e13-2 - e13-3 Lifter switch on 4.8 to 5.1 V

for RHD
Tester Connection Condition Specified Condition
e30-2 - e30-3 Lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)))
5.CHECK LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
a.
B517917C78
1.115,0.167 1.531,0.417 0.417,0.25 1.865,0.167 2.281,0.417 0.417,0.25 0.156,0.146 0.396,0.396 0.24,0.25 10 false *a 1.219,0.208 1.594,0.479 0.375,0.271 10 false e13 1.583,0.198 1.958,0.469 0.375,0.271 12 false *A 1.958,0.208 2.333,0.479 0.375,0.271 10 false e30 2.344,0.208 2.719,0.479 0.375,0.271 12 false *B
*A for LHD
*B for RHD
*a Component with harness connected
(Lifter Motor (Power Seat Lifter Motor Assembly (Driver Seat)))


Reconnect the e13*1 or e30*2 lifter motor (power seat lifter motor assembly (driver seat)) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
e13-2 - Body ground Lifter motor operating 4.5 to 4.8 V

for RHD
Tester Connection Condition Specified Condition
e30-2 - Body ground Lifter motor operating 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPLACE LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the e25 position control ECU assembly (driver seat) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e25-25 (SSRL) - e13-2 Always Below 1 Ω
e25-25 (SSRL) or e13-2 - Body ground Always 10 kΩ or higher
e25-12 (SGND) - e13-3 Always Below 1 Ω
e25-12 (SGND) or e13-3 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
e25-25 (SSRL) - e30-2 Always Below 1 Ω
e25-25 (SSRL) or e30-2 - Body ground Always 10 kΩ or higher
e25-12 (SGND) - e30-3 Always Below 1 Ω
e25-12 (SGND) or e30-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))

OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)))

NG

REPLACE LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - LIFTER MOTOR (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the e23 and e24 position control ECU assembly (driver seat) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
e23-6 (LFT+) - e13-1 Always Below 1 Ω
e23-6 (LFT+) or e13-1 - Body ground Always 10 kΩ or higher
e24-5 (LFT-) - e13-4 Always Below 1 Ω
e24-5 (LFT-) or e13-4 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
e23-6 (LFT+) - e30-1 Always Below 1 Ω
e23-6 (LFT+) or e30-1 - Body ground Always 10 kΩ or higher
e24-5 (LFT-) - e30-4 Always Below 1 Ω
e24-5 (LFT-) or e30-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR