This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2658 | Short in Sensor with Motor Power Supply Circuit | Problem with the voltage supplied to the position control sensor. | ·
Position control ECU assembly (driver seat) ·
Slide motor (separate type front seat cushion spring assembly (driver seat)) ·
Front vertical motor (power seat tilt motor assembly (driver seat)) ·
Lifter motor (power seat lifter motor assembly (driver seat)) ·
Reclining motor (separate type front seatback spring assembly (driver seat)) ·
Wire harness or connector |
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B2658 is not output.
| Result | Proceed to |
|---|---|
| DTC B2658 is not output | A |
| DTC B2658 output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the e25 position control ECU assembly (driver seat) connector.
Disconnect the e11*1 or e28*2 slide motor (separate type front seat cushion spring assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-26 (SSRS) - e11-2 | Always | Below 1 Ω |
| e25-26 (SSRS) or e11-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - e11-3 | Always | Below 1 Ω |
| e25-12 (SGND) or e11-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-26 (SSRS) - e28-2 | Always | Below 1 Ω |
| e25-26 (SSRS) or e28-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - e28-3 | Always | Below 1 Ω |
| e25-12 (SGND) or e28-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the e11*1 or e28*2 slide motor (separate type front seat cushion spring assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e11-2 - e11-3 | Slide switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e28-2 - e28-3 | Slide switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e25 position control ECU assembly (driver seat) connector.
Disconnect the e12*1 or e29*2 front vertical motor (power seat tilt motor assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-10 (SSFV) - e12-2 | Always | Below 1 Ω |
| e25-10 (SSFV) or e12-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - e12-3 | Always | Below 1 Ω |
| e25-12 (SGND) or e12-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-10 (SSFV) - e29-2 | Always | Below 1 Ω |
| e25-10 (SSFV) or e29-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - e29-3 | Always | Below 1 Ω |
| e25-12 (SGND) or e29-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the e12*1 or e29*2 front vertical motor (power seat tilt motor assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e12-2 - e12-3 | Front vertical switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e29-2 - e29-3 | Front vertical switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e25 position control ECU assembly (driver seat) connector.
Disconnect the e13*1 or e30*2 lifter motor (power seat lifter motor assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-25 (SSRL) - e13-2 | Always | Below 1 Ω |
| e25-25 (SSRL) or e13-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - e13-3 | Always | Below 1 Ω |
| e25-12 (SGND) or e13-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-25 (SSRL) - e30-2 | Always | Below 1 Ω |
| e25-25 (SSRL) or e30-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - e30-3 | Always | Below 1 Ω |
| e25-12 (SGND) or e30-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the e13*1 or e30*2 lifter motor (power seat lifter motor assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e13-2 - e13-3 | Lifter switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e30-2 - e30-3 | Lifter switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e25 position control ECU assembly (driver seat) connector.
Disconnect the g5*1 or g7*2 reclining motor (separate type front seatback spring assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-11 (SSRR) - g5-2 | Always | Below 1 Ω |
| e25-11 (SSRR) or g5-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - g5-3 | Always | Below 1 Ω |
| e25-12 (SGND) or g5-3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e25-11 (SSRR) - g7-2 | Always | Below 1 Ω |
| e25-11 (SSRR) or g7-2 - Body ground | Always | 10 kΩ or higher |
| e25-12 (SGND) - g7-3 | Always | Below 1 Ω |
| e25-12 (SGND) or g7-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the g5*1 or g7*2 reclining motor (separate type front seatback spring assembly (driver seat)) connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| g5-2 - g5-3 | Reclining switch on | 4.8 to 5.1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| g7-2 - g7-3 | Reclining switch on | 4.8 to 5.1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front vertical motor (power seat tilt motor assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the lifter motor (power seat lifter motor assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the slide motor (separate type front seat cushion spring assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the reclining motor (separate type front seatback spring assembly (driver seat)) with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B2658 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG