When the seat heater switch of the front seat heater switch (air conditioning control assembly) is operated, the air conditioning amplifier assembly receives a signal and operates the front seat heater.
If the auxiliary battery voltage is low, the seat heater system may not operate. If "High Power Consumption Power to Climate Temporarily Limited" is displayed on the multi-information display in the combination meter assembly, inspect the auxiliary battery, referring to On-vehicle Inspection of Charging System.
If the auxiliary battery voltage becomes low, auxiliary battery load control will operate in order to ensure sufficient power is supplied to the power steering system. In this case, the seat heater system may not operate.
Inspect the fuses for circuits related to this system before performing the following procedure.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
DTC B14B5 and B14C0 are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Front Right Seat Heater | Front seat RH side seat heater operation | OFF or ON | - |
| Tester Display |
|---|
| Front Right Seat Heater |
The seat heater operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Seat Heater Control Sub-assembly RH (for Front)) |
Disconnect the e10 seat heater control sub-assembly RH (for front) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e10-1 (+B1) - Body ground | Ignition switch ON | 11 to 14 V |
| e10-1 (+B1) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER (for Manual Seat)>INSPECTION
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER (for Manual Seat)>REMOVAL
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEATBACK HEATER (for Power Seat)>REMOVAL
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER (for Manual Seat)>INSPECTION
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER (for Power Seat)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Manual Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER (for Manual Seat)>REMOVAL
for Power Seat: Click hereVehicle Interior>SEAT>FRONT SEAT CUSHION HEATER (for Power Seat)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e8-2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e10-7 (HTR1) - e8-1 | Always | Below 1 Ω |
| e10-7 (HTR1) or e8-1 - Body ground | Always | 10 kΩ or higher |
| e10-10 (E) - e8-6 | Always | Below 1 Ω |
| e10-10 (E) or e8-6 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the e10 seat heater control sub-assembly RH (for front) connector.
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the H64 air conditioning amplifier assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H64-12 (SM1R) - Body ground | Ignition switch ON | 5 to 13 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the e10 seat heater control sub-assembly RH (for front) connector.
Reconnect the H64 air conditioning amplifier assembly connector.
Remove the air conditioning amplifier assembly with its connectors still connected.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H64-12 (SM1R) - H62-17 (GND) | Ignition switch ON, front seat heater switch (air conditioning control assembly) on (LO) | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e10 seat heater control sub-assembly RH (for front) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H64-12 (SM1R) - e10-5 (SWR) | Always | Below 1 Ω |
| H64-12 (SM1R) or e10-5 (SWR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the S/HTR F/R relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S/HTR F/R relay holder terminal 1 - Body ground | Ignition switch ON | 11 V to 14 V |
| S/HTR F/R relay holder terminal 1 - Body ground | Ignition switch off | Below 1 V |
| S/HTR F/R relay holder terminal 3 - Body ground | Ignition switch off*1
Always*2 |
11 V to 14 V |
*1: for HV Model
*2: for Gasoline Model
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S/HTR F/R relay holder terminal 5 - e10-1 (+B1) | Always | Below 1 Ω |
| S/HTR F/R relay holder terminal 5 or e10-1 (+B1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S/HTR F/R relay holder terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG