Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086894 SEAT _0420117 SEAT HEATER SYSTEM J

SEAT  SEAT HEATER SYSTEM  Seat Heater for Rear Left Seat does not Operate  


DESCRIPTION

When the rear seat heater switch (air conditioning control assembly No. 2) is operated, the air conditioning amplifier assembly receives the signal and operates the seat heater for the corresponding rear seat.

WIRING DIAGRAM

B567558E15
0.813,0.469 1.427,0.667 0.615,0.198 10 false RLIN 1.219,4.802 1.677,5 0.458,0.198 10 false H62 2.417,2.24 3.792,2.438 1.375,0.198 10 false S/HTR R/L 5.063,1.479 7.115,1.823 2.052,0.344 10 false from IG1-NO. 1 Relay 4.531,0.625 4.99,0.823 0.458,0.198 10 false T2 4.531,0.802 7.094,1.198 2.563,0.396 10 false Rear Seat Heater Switch (Air Conditioning Control Assembly No. 2) 5.135,0.448 5.677,0.74 0.542,0.292 10 false RLIN 2.115,3.177 2.448,3.375 0.333,0.198 10 false +B1 1.833,5.177 2.292,5.375 0.458,0.198 10 false f7 1.823,5.333 3.375,6.052 1.552,0.719 10 false Seat Heater Control Sub-assembly LH (for Rear) 3.521,5.198 5.354,5.792 1.833,0.594 10 false Rear Seat Cushion Heater LH (Seat Heater Assembly) 0.083,5.188 1.635,5.875 1.552,0.688 10 false Air Conditioning Amplifier Assembly 0.833,6.292 4.5,6.49 3.667,0.198 10 false : LIN Communication Line 1.26,4.615 1.583,4.958 0.323,0.344 10 false 17 1.979,4.271 2.135,4.469 0.156,0.198 10 false 5 3.073,1.854 3.385,2.052 0.313,0.198 10 false 3 4.917,0.292 5.531,0.51 0.615,0.219 10 false 8 0.823,4.792 1.281,4.99 0.458,0.198 10 false GND 1.24,4.198 1.688,4.573 0.448,0.375 10 false 24 1.208,4.385 1.667,4.583 0.458,0.198 10 false H64 0.74,4.385 1.198,4.583 0.458,0.198 10 false SM2L 1.958,3.042 2.115,3.24 0.156,0.198 10 false 1 1.219,0.458 1.677,0.656 0.458,0.198 10 false H64 2.125,4.385 2.583,4.583 0.458,0.198 10 false SWR 2.667,3.177 3.104,3.448 0.438,0.271 10 false HTR1 2.896,4.385 3.354,4.583 0.458,0.198 10 false E 3.635,4.802 4.094,5 0.458,0.198 10 false f5 5.552,5.198 7.125,5.75 1.573,0.552 10 false Rear Seatback Heater LH (Seat Heater Assembly) 3.052,4.281 3.323,4.563 0.271,0.281 10 false 10 3.083,3.073 3.24,3.271 0.156,0.198 10 false 7 3.656,2.979 3.813,3.177 0.156,0.198 10 false 1 3.656,4.188 3.813,4.385 0.156,0.198 10 false 3 5.417,3.177 5.875,3.375 0.458,0.198 10 false C 5.417,4.375 5.875,4.573 0.458,0.198 10 false C 3.646,4.365 4.104,4.563 0.458,0.198 10 false f5 3.615,3.167 4.073,3.365 0.458,0.198 10 false f5 3.656,4.625 3.813,4.823 0.156,0.198 10 false 4 4.073,2.115 5.448,2.313 1.375,0.198 10 false S/HTR R/L 3.927,1.615 5.302,1.813 1.375,0.198 10 false ECU-IG1 NO. 3 5.073,1.948 6.792,2.188 1.719,0.24 10 false from Auxiliary Battery 2.365,1.365 2.677,1.563 0.313,0.198 10 false 2 3.063,1.375 3.375,1.573 0.313,0.198 10 false 1 2.375,1.854 2.688,2.052 0.313,0.198 10 false 5 1.25,0.24 1.594,0.469 0.344,0.229 10 false 20

CAUTION / NOTICE / HINT

NOTICE:
·

If the battery voltage is low, the seat heater system may not operate. If "High Power Consumption Power to Climate Temporarily Limited" is displayed on the multi-information display in the combination meter assembly, inspect the battery, referring to On-vehicle Inspection of Charging System.

·

If the battery voltage becomes low, battery load control will operate in order to ensure sufficient power is supplied to the power steering system. In this case, the seat heater system may not operate.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Air Conditioner > Clear DTCs
50002 121

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B14B3 or B14C3 is not output.


Result:
Proceed to
OK
NG




OK

3.PERFORM ACTIVE TEST USING GTS

NG

3.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Left Seat Heater Rear seat LH side seat heater operation OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Rear Left Seat Heater
50004 121 119
OK:

The seat heater operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE REAR SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY NO. 2)

NG

4.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR))
4.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR))
a.
B569382C04
1.479,0.125 1.938,0.406 0.458,0.281 0.677,1.26 1.094,1.26 true 0.313,0.229 0.625,0.385 0.313,0.156 10 false *a 1.656,0.177 2.25,0.469 0.594,0.292 10 false f7 0.406,1.177 0.865,1.375 0.458,0.198 10 false +B1
*a Front view of wire harness connector
(to Seat Heater Control Sub-assembly LH (for Rear))


Disconnect the f7 seat heater control sub-assembly LH (for rear) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
f7-1 (+B1) - Body ground Ignition switch ON 11 to 14 V
f7-1 (+B1) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.INSPECT REAR SEATBACK HEATER LH (SEAT HEATER ASSEMBLY)

NG

12.INSPECT S/HTR R/L RELAY
5.INSPECT REAR SEATBACK HEATER LH (SEAT HEATER ASSEMBLY)

OK

6.INSPECT REAR SEAT CUSHION HEATER LH (SEAT HEATER ASSEMBLY)

NG

REPLACE REAR SEATBACK HEATER LH (SEAT HEATER ASSEMBLY)

6.INSPECT REAR SEAT CUSHION HEATER LH (SEAT HEATER ASSEMBLY)

OK

7.CHECK HARNESS AND CONNECTOR (REAR SEAT CUSHION HEATER LH (SEAT HEATER ASSEMBLY) - BODY GROUND)

NG

REPLACE REAR SEAT CUSHION HEATER LH (SEAT HEATER ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (REAR SEAT CUSHION HEATER LH (SEAT HEATER ASSEMBLY) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
f5-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR) - REAR SEAT CUSHION HEATER LH (SEAT HEATER ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR) - REAR SEAT CUSHION HEATER LH (SEAT HEATER ASSEMBLY))
a.

Disconnect the f7 seat heater control sub-assembly LH (for rear) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
f7-7 (HTR1) - f5-1 Always Below 1 Ω
f7-7 (HTR1) or f5-1 - Body ground Always 10 kΩ or higher
f7-10 (E) - f5-3 Always Below 1 Ω
f7-10 (E) or f5-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR)
a.

Reconnect the f7 seat heater control sub-assembly LH (for rear) connector.


b.
B569383C04
1.469,0.135 1.958,0.438 0.49,0.302 2.823,1.958 1.938,1.51 true 1.594,0.198 2.052,0.396 0.458,0.198 10 false H64 0.104,0.073 0.563,0.271 0.458,0.198 10 false *a 2.885,1.896 3.344,2.094 0.458,0.198 10 false SM2L
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the H64 air conditioning amplifier assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H64-24 (SM2L) - Body ground Ignition switch ON 5 to 13 V



Result:
Proceed to
OK
NG



OK

10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR))
10.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the f7 seat heater control sub-assembly LH (for rear) connector.


b.

Reconnect the H64 air conditioning amplifier assembly connector.


c.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


d.

Measure the voltage according to the value(s) in the table below.

E435041C04
2.729,0.115 3.083,0.375 0.354,0.26 4.75,0.115 5.104,0.375 0.354,0.26 0.615,1.604 0.771,1.604 0.771,1.604 2.792,1.188 true 4.531,1.094 6.531,1.479 6.531,1.479 6.688,1.479 true 0.385,0.24 0.625,0.521 0.24,0.281 10 false *a 2.781,0.156 3.167,0.427 0.385,0.271 10 false H64 4.802,0.156 5.198,0.438 0.396,0.281 10 false H62 0.188,1.51 0.677,1.76 0.49,0.25 10 false SM2L 6.729,1.385 7.094,1.573 0.365,0.188 10 false GND
*a Component with harness connected
(Air Conditioning Amplifier Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
H64-24 (SM2L) - H62-17 (GND) Ignition switch ON, rear seat heater switch (air conditioning control assembly No. 2) on (LO) Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR))
a.

Disconnect the f7 seat heater control sub-assembly LH (for rear) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H64-24 (SM2L) - f7-5 (SWR) Always Below 1 Ω
H64-24 (SM2L) or f7-5 (SWR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT S/HTR R/L RELAY
a.

Inspect the S/HTR R/L relay.

Click hereVehicle Interior>SEAT>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - S/HTR R/L RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (POWER SUPPLY - S/HTR R/L RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
S/HTR R/L relay holder terminal 1 - Body ground Ignition switch ON 11 V to 14 V
S/HTR R/L relay holder terminal 1 - Body ground Ignition switch off Below 1 V
S/HTR R/L relay holder terminal 3 - Body ground Ignition switch off*1
Always*2
11 V to 14 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (S/HTR R/L RELAY - SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (S/HTR R/L RELAY - SEAT HEATER CONTROL SUB-ASSEMBLY LH (FOR REAR))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S/HTR R/L relay holder terminal 5 - f7-1 (+B1) Always Below 1 Ω
S/HTR R/L relay holder terminal 5 or f7-1 (+B1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (S/HTR R/L RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (S/HTR R/L RELAY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S/HTR R/L relay holder terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR