Home › Brake › BRAKE (FRONT) › FRONT BRAKE › from 2020.11
RM37A0E _54 Brake _086870 BRAKE (FRONT) _0420815 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front brake removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When removing or installing the front disc brake cylinder assembly, pushing back the disc brake piston may cause a large clearance between the brake pads and brake disc. When the brake pedal is depressed with a large clearance between the brake pads and the brake disc, DTC C13DB00, C13DC00, C13DD00, C13DE00, C140000 and/or C140A00 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model)

·

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)

·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for HV Model)



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.DISABLE BRAKE CONTROL (for HV Model)

a.

Wait 4 minutes after turning the ignition switch off to ensure that the skid control ECU is in sleep mode.

NOTICE:

When the brake pedal is depressed or the door courtesy switch is turned on even if the ignition switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



b.

for LHD:

i.
C426266

Disengage the clamp to separate the wire harness from the brake master cylinder reservoir assembly.


ii.

Remove the bolt and nut and separate the brake master cylinder reservoir assembly.


iii.
C426267

Disconnect the connector from the brake master cylinder reservoir assembly.


iv.

Return the brake master cylinder reservoir assembly to its original position.

HINT:

Do this to prevent brake fluid leakage.




c.

for RHD:

i.

Disconnect the connector from the brake master cylinder reservoir assembly.



d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL


e.

In order to prevent pressurized brake fluid in the accumulator from being applied to the brake calipers, depress the brake pedal 40 times or more to return the pressurized brake fluid in the accumulator back to the brake master cylinder reservoir assembly.


f.

Check that the brake pedal cannot be further depressed.


Hide 2.REMOVE FRONT WHEEL

Hide 3.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47313J 4.DISCONNECT FRONT FLEXIBLE HOSE

a.
C423856

Remove the union bolt and gasket, and disconnect the front flexible hose from the front disc brake cylinder assembly.


Hide 47750 5.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY

a.
C423857C01
1,1.542 1.313,1.698 0.313,0.156 10 false *a 2.031,1.479 2.208,1.625 0.177,0.146 10 true *b
*a Turn
*b Hold


Hold the 2 front disc brake cylinder slide pins and remove the 2 bolts and front disc brake cylinder assembly.


Hide 6.REMOVE FRONT DISC BRAKE PAD

a.
C423858

Remove the 2 anti-squeal springs.


b.
C423859

Remove the 2 front disc brake pads from the front disc brake cylinder mounting.


Hide 04945 7.REMOVE FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 8.REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE

a.
C423860C01
0,0 0,0 false

Remove the 4 front disc brake pad support plates from the front disc brake cylinder mounting.

NOTICE:

Each front disc brake pad support plate has a different shape. Be sure to put an identification mark on each front disc brake pad support plate so that it can be reinstalled to its original position.



Hide 47715A 9.REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C423861

Remove the 2 front disc brake cylinder slide pins from the front disc brake cylinder mounting.


b.
C423862C01
2.219,1.25 2.469,0.833 2.469,0.833 2.688,0.833 false 2.74,0.76 3.052,0.917 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the front disc brake cylinder slide bushing from the front disc brake cylinder slide pin (lower side).

NOTICE:

Do not damage the front disc brake cylinder slide pin.



Hide 10.REMOVE FRONT DISC BRAKE BUSHING DUST BOOT

a.
C423863

Remove the 2 front disc brake bushing dust boots from the front disc brake cylinder mounting.


Hide 47722 11.REMOVE FRONT DISC BRAKE CYLINDER MOUNTING

a.
C423864

Remove the 2 bolts and front disc brake cylinder mounting from the steering knuckle.


Hide 43512 12.REMOVE FRONT DISC

a.
C423865C01
2.042,1.156 2.604,1.156 2.604,1.156 2.604,1.042 true 2.01,1.052 2.76,1.052 true 2.792,0.948 3.104,1.146 0.313,0.198 10 false *a
*a Matchmark


Put matchmarks on the front disc and the front axle hub sub-assembly.


b.

Remove the front disc.