Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (EMISSION CONTROL) › EGR VALVE › from 2021.10
RM37A0E _51 Engine / Hybrid System _086908 A25A-FXS, A25B-FXS EMISSION CONTROL _0416572 EGR VALVE A

A25A-FXS, A25B-FXS EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC is output (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)for 2WD
(Click here)for 4WD/AWD
·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 2.DISCONNECT ENGINE WIRE

a.
A493115C03
1.531,1.302 1.729,0.885 1.729,0.885 1.948,0.885 true 0.99,1.969 1.24,1.969 1.24,1.969 1.406,1.552 true 1.969,0.802 2.208,0.979 0.24,0.177 10 true *1 0.802,1.896 1.042,2.094 0.24,0.198 10 true *2
*1 No. 1 Fuel Vapor Feed Hose
*2 No. 2 Fuel Vapor Feed Hose


Disengage the 3 hose clamps and disconnect the No. 1 fuel vapor feed hose and No. 2 fuel vapor feed hose.


b.
A493116

Disconnect the EGR valve assembly connector.


c.

Remove the bolt.


d.

Disengage the 2 wire harness clamps and disconnect the engine wire.


Hide 25601 3.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A493117

Using an 8 mm socket wrench, remove the 4 bolts and No. 1 EGR pipe sub-assembly from the intake manifold and EGR valve assembly.


b.
A472576

Remove the EGR valve adapter gasket from the No. 1 EGR pipe sub-assembly.


c.
A402227

Remove the EGR inlet gasket from the intake manifold.


Hide 25620 4.REMOVE EGR VALVE ASSEMBLY

a.
A472577C01
1.719,0.594 1.917,0.25 1.917,0.25 2.188,0.25 true 2.094,2 1.813,2 1.813,2 1.688,1.531 true 2.292,0.167 2.563,0.375 0.271,0.208 10 true *2 2.177,1.917 2.469,2.125 0.292,0.208 10 true *1
*1 No. 8 Water By-pass Hose
*2 No. 4 Water By-pass Hose


Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.


b.

Slide the clip and remove the No. 4 water by-pass hose from the EGR valve assembly.


c.
A472578

Using an 8 mm socket wrench, remove the 2 bolts and EGR valve assembly from the camshaft housing.