Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2021.10
RM37A0E _51 Engine / Hybrid System _086909 A25A-FXS, A25B-FXS INTAKE / EXHAUST _0416453 INTAKE MANIFOLD A

A25A-FXS, A25B-FXS INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 22030 1.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25601 3.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 89421 4.REMOVE E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Hide 82121 6.DISCONNECT ENGINE WIRE

a.
A455264

Disconnect the No. 5 engine wire connector.


b.

Remove the bolt and disconnect the engine wire from the cylinder head sub-assembly.


c.
A455265

Remove the bolt.


d.

Disengage the wire harness clamp and disconnect the engine wire from the intake manifold.


Hide 16279 7.DISCONNECT NO. 3 WATER BY-PASS PIPE

a.
A455266

Slide the clip and disconnect the No. 5 water by-pass hose from the No. 3 water by-pass pipe.


b.

Using an 8 mm socket wrench, remove the bolt and disconnect the No. 3 water by-pass pipe from the intake manifold.


Hide 16278 8.REMOVE NO. 2 WATER BY-PASS PIPE

a.
A455267N01
0.927,1.708 1.073,1.875 0.146,0.167 10 true A 2.188,1.729 2.354,1.896 0.167,0.167 10 true B 0.917,0.406 1.073,0.583 0.156,0.177 10 true A

Disengage the wire harness clamp and disconnect the HV air conditioning wire.


b.

Using an 8 mm socket wrench, remove the 2 bolts (A) and separate the No. 2 water by-pass pipe from the intake manifold.


c.

Remove the bolt (B) and No. 2 water by-pass pipe from the cylinder block sub-assembly.


Hide 23820 9.REMOVE NO. 2 FUEL VAPOR FEED HOSE

a.
A455268

Remove the No. 2 fuel vapor feed hose from the intake manifold.


Hide 17111 10.REMOVE INTAKE MANIFOLD

a.
A455269

w/o Stud Bolt:

i.

Remove the 5 bolts and intake manifold from the cylinder head sub-assembly.



b.
A449081

w/ Stud Bolt:

i.

Remove the 3 bolts and 2 nuts.


ii.
A449082

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and intake manifold from the cylinder head sub-assembly.



Hide 17177 11.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A402294

Remove the No. 1 intake manifold to head gasket from the intake manifold.


Hide 12611B 12.REMOVE NO. 1 ENGINE COVER

a.
A402295

Remove the clip and No. 1 engine cover.


Hide 13.REMOVE VACUUM HOSE

a.
A402296

Remove the vacuum hose from the intake manifold.