2008-2009 Hilux TRD · Service Manual Brake

Brake System

Brake

PRECAUTION
NOTICE:
• Care must be taken to replace each part correctly, as the performance of the brake system could be affected resulting in a driving hazard. Replace the parts with those having the same part number or equivalent.
• When repairing the brake system, keep the parts and work area clean.
• Care must be taken if using a magnet as it may affect the performance of the speed sensors.
• Since the brake line is one of the critical safety related parts, disassemble the components if a brake fluid leak is found. If any abnormality is found, replace the component with a new one.
• When removing brake components, cover the brake tube connections to prevent foreign matter such as dust or dirt from entering the tubes.
• Do not damage or deform the brake tubes when removing or installing them.
• When installing a grommet to the body, ensure the brake tube passes through the centre of the grommet.
• When installing a brake tube or flexible hose, ensure it is free from twisting or bending.
• If the cap of the flexible hose does not match the groove on the bracket, twist the hose slightly to insert it.
• Do not reuse a clip removed from a flexible hose.
• Flexible hoses must be free from oil, grease, etc.
• When installing a brake tube to a plastic clamp, ensure the brake tube is not loose or being pinched.
• Do not reuse a clip or plastic clamp removed from a flexible hose.
• After installing a brake tube and flexible hose, ensure they do not interfere with any other components.
• Do not allow brake fluid to contact any painted surface such as the vehicle body. If brake fluid leaks onto any painted surface, immediately wash it off.


• Follow these procedures when disconnecting and connecting the flexible hose and brake tube.
(a) Remove the clip.
(b) Hold the flexible hose with a wrench and disconnect the brake tube with SST without deforming the tube.
(c) Connect the brake tube with a union nut wrench without deforming the tube.


• Follow these procedures when connecting the brake tube and way.
(a) Support the way to prevent deformation to the brake tube and connect the brake tube to the way with a union nut wrench.
(b) Support the way to prevent deformation to the brake tube and install the bolt to fix the way to the body.
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of the problem symptom. The potential causes of the symptoms are listed in order of probability in the Suspected Area column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Symptom
Suspected Area
See page
Low pedal or spongy pedal
1. Fluid leaks in brake system
-
2. Air in brake system
Click Here
3. Rear brake shoe clearance (adjustment)
XX : rm0000010qs000x_02_0008
4. Piston seals (worn or damaged)
Click Here
5. Brake master cylinder (faulty)
XX : rm0000010ke005x_
6. Booster push rod (adjustment necessary)
XX : rm000001l5n00ex_01_0001
Brake drag
1. Brake pedal free play (minimal)
XX : rm0000010k5000x_
2. Parking brake lever travel (adjustment)
XX : rm0000010m1000x_01_0004
3. No. 1 parking brake wire (stuck)
XX : RM0000010QV000X_01_0007
4. No. 2 parking brake wire (stuck)
XX : RM0000010QV000X_01_0008
5. No. 3 parking brake wire (stuck)
XX : RM0000010QV000X_01_0009
6. Rear brake shoe clearance (adjustment)
XX : rm0000010qs000x_02_0008
7. Pad (cracked or distorted)
Click Here
8. Lining (cracked or distorted)
XX : rm0000010qo000x_
9. Front brake piston (stuck)
Click Here
10. Rear brake piston (stuck)
XX : rm0000010qr000X_
11. Tension or return spring (faulty)
XX : rm0000010qr000x_
12. Booster push rod (adjustment)
XX : rm000001l5n00ex_01_0001
13. Vacuum leaks in booster system
XX : rm0000010kj003x_
14. Brake master cylinder (faulty)
XX : rm0000010ke005x_
Brake pull
1. Front brake piston (stuck or frozen)
Click Here
2. Rear brake piston (stuck or frozen)
XX : rm0000010qr000x_
3. Pad (oily, cracked or distorted)
Click Here
4. Lining (oily, cracked or distorted)
XX : rm0000010qo000x_
5. Disc (scored)
Click Here
Brake pedal is depressed firmly but brake is insufficient
1. Fluid leaks in brake system
-
2. Air in brake system
Click Here
3. Pad (worn, cracked, distorted, oily or glazed)
Click Here
4. Lining (worn, cracked, distorted, oily or glazed)
XX : rm0000010qo000x_
5. Rear brake shoe clearance (adjustment)
XX : rm0000010qs000x_02_0008
6. Disc (scored)
Click Here
7. Booster push rod (adjustment)
XX : rm000001l5n00ex_01_0001
8. Vacuum leaks in booster system
XX : rm0000010kj003x_
Noise from brakes
1. Pad (cracked, distorted, dirty or glazed)
Click Here
2. Lining (cracked, distorted, dirty or glazed)
XX : rm0000010qo000x_
3. Installation bolt
Click Here
4. Disc (scored)
Click Here
5. Anchor, return or tension spring (faulty)
XX : rm0000010qr000x_
6. Anti squeal shim (damaged)
Click Here
7. Shoe hold down spring (damaged)
XX : rm0000010qr000x_