Front Brake
Brake
COMPONENTS

REMOVAL
HINT:
• Use the same procedures for the LH side and RH side.
• The procedures listed below are for the LH side.
1. REMOVE FRONT WHEEL
2. DRAIN BRAKE FLUID
NOTICE:
Wash off brake fluid immediately if it comes in contact with any painted surface.
3. REMOVE FRONT DISC BRAKE ANTI-RATTLE W/ HOLE PIN
(a) Remove the 2 pin hole clips.
-
(b) Remove the 2 anti-rattle w/ hole pins.
-
(c) Remove the anti-rattle spring.
CAUTION:
Do not remove the lower pin without holding down the spring.
-
4. REMOVE FRONT DISC BRAKE PAD
(a) Remove the 2 disc brake pads with the anti-squeal shims from the brake cylinder assembly.
-
5. REMOVE ANTI-SQUEAL SHIM
(a) Remove the anti-squeal shims from the brake pads.
-
6. REMOVE DISC BRAKE CYLINDER ASSEMBLY
(a) Using SST, disconnect the brake tube from the cylinder.
SST
09023-00101
HINT:
Use a container to catch the brake fluid as it drains.
-
(b) Remove the 2 bolts and the disc brake cylinder assembly.
-
DISASSEMBLY
1. REMOVE CYLINDER BOOT
(a) Using a screwdriver, remove the 4 boots from the brake cylinder.
NOTICE:
Be careful not to damage the cylinder and piston.
-
2. REMOVE FRONT DISC BRAKE PISTON
(a) Prepare a wooden plate to hold the pistons.
-
(b) Place the plate between the pistons and insert a pad on one side.
-
(c) Use compressed air to remove the pistons alternately from the cylinder.
CAUTION:
Do not place your finger in front of the piston when using compressed air.
NOTICE:
Be careful not to spatter the brake fluid.
-
3. REMOVE PISTON SEAL
(a) Using a screwdriver, remove the 4 piston seals from the cylinder.
NOTICE:
Be careful not to damage the inner cylinder and cylinder groove.
-
4. REMOVE FRONT DISC BRAKE BLEEDER PLUG
(a) Remove the bleeder plug cap and bleeder plug from the cylinder.
-
5. REMOVE FRONT DISC
(a) Put matchmarks on the disc and axle hub.
-
(b) Remove the disc.
-
INSPECTION
1. CHECK BRAKE CYLINDER AND PISTON
(a) Check the cylinder bore and piston for rust or scoring.
If necessary, replace the cylinder and piston.
-
2. CHECK PAD LINING THICKNESS
(a) Using a ruler, measure the pad lining thickness.
Standard thickness:
11.5 mm (0.453 in.)
Minimum thickness:
1.0 mm (0.039 in.)
If the pad lining thickness is equal to or less than the minimum, replace the pad.
-
3. CHECK DISC THICKNESS
(a) Using a micrometer, measure the disc thickness.
Standard thickness:
28.0 mm (1.102 in.)
Minimum thickness:
26.0 mm (1.024 in.)
If the disc thickness is less than the minimum, replace the disc.
-
REASSEMBLY
1. INSTALL FRONT DISC
(a) Align the matchmarks and install the disc.
HINT:
When replacing the disc with a new one, select the installation position where the disc has the minimum runout.
-
2. CHECK DISC RUNOUT
(a) Check the bearing backlash and check the axle hub deviation (
Click Here
)
-
(b) Temporarily install the disc with the hub nuts.
-
(c) Using a dial indicator, measure the disc runout 10 mm (0.39 in.) from the outer edge of the disc.
Maximum disc runout:
0.05 mm (0.0020 in.)
If the runout is greater than the maximum, change the installation position of the disc and axle so the runout will become minimal. If the runout is greater than the maximum, even when the installation positions are changed, grind the disc. If the disc thickness is less than the minimum, replace the disc.
-
(d) Remove the 2 nuts.
-
3. TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG
(a) Install the bleeder plug to the cylinder.
HINT:
The bleeder plug will be tightened to a torque specification in the Bleed Air From Brake Line procedure.
-
(b) Install the cap to the bleeder plug.
-
4. INSTALL PISTON SEAL
(a) Apply lithium soap base glycol grease to 4 new seals.
-
(b) Install the 4 piston seals to the cylinder.
-
5. INSTALL FRONT DISC BRAKE PISTON
(a) Apply lithium soap base glycol grease to the 4 pistons.
-
(b) Install the 4 pistons to the cylinder.
NOTICE:
Do not forcibly install the pistons to the cylinder.
-
6. INSTALL CYLINDER BOOT
(a) Apply lithium soap base glycol grease to the 4 cylinder boots.
-
(b) Install 4 new boots to the cylinder.
HINT:
Install the cylinder boot securely on the grooves of the cylinder and piston.
-
INSTALLATION
1. INSTALL DISC BRAKE CYLINDER ASSEMBLY
(a) Install the cylinder with the 2 bolts.
Torque:
123 N*m
(1,254 kgf*cm,
91 ft.*lbf)
-
2. CONNECT FRONT NO. 1 WHEEL CYLINDER TUBE
(a) Using SST, connect the tube to the cylinder.
SST
09023-00101
Torque:
15.2 N*m
(155 kgf*cm,
11 ft.*lbf)
-
3. INSTALL FRONT ANTI SQUEAL SHIM
(a) Install the 2 anti-squeal shims to each brake pad.
NOTICE:
• When replacing worn pads, the shims must be replaced together with the pads.
• Install the shims in the correct position and direction.
-
4. INSTALL FRONT DISC BRAKE PAD
(a) Install the 2 disc brake pads to the cylinder.
NOTICE:
There should be no oil or grease on the friction surface of the pads and disc.
-
5. INSTALL FRONT DISC BRAKE ANTI-RATTLE W/ HOLE PIN
(a) Install the spring.
-
(b) Hold down the spring and insert the lower pin and upper pin.
-
(c) Install the clips.
NOTICE:
Install the clips with the handle facing the vehicle centre.
-
6. FILL RESERVOIR WITH BRAKE FLUID (
Click Here
)
7. BLEED AIR FROM BRAKE LINE (
Click Here
)
8. CHECK BRAKE FLUID LEVEL IN RESERVOIR (
Click Here
)
9. CHECK FOR BRAKE FLUID LEAKAGE
10. INSTALL FRONT WHEEL